I've find out they are resistors, can someone measure their resistance?Up. Anyone know if I have to replace the caps and if i can use the pi-zero`s one.
I've find out they are resistors, can someone measure their resistance?Up. Anyone know if I have to replace the caps and if i can use the pi-zero`s one.
I was so consumed with the multimeter reading that I didn't bother to try it out. Thank you! It did work. I have officially glitched a Switch with a MOSFET.since its runing fine now with the 2 caps stollen from the rp go ahead and reinstall the pico with the caps on it should work
Bevor u start cutting check the aio thread for the pinout and cutting linesI was so consumed with the multimeter reading that I didn't bother to try it out. Thank you! It did work. I have officially glitched a Switch with a MOSFET.
View attachment 366994
Now on to my next challenge. I bought this big grinder to cut the pico precisely. This is exciting.
View attachment 366995
HELP!!!
tasukette!!!
recently im trying to remove my micro sd on lite slot...
i think my micro sd stuck ...
but the switch still read the micro sd when i turn it on...
does it bounce back when we press the micro sd???
when i press the micro sd... it feel hard and nothing bounce ??
View attachment 366997
thats what im afraidEject spring might be broken.
Congratulations man, you had an exiting weekI was so consumed with the multimeter reading that I didn't bother to try it out. Thank you! It did work. I have officially glitched a Switch with a MOSFET.
View attachment 366994
Now on to my next challenge. I bought this big grinder to cut the pico precisely. This is exciting.
View attachment 366995
Thank you for your help! I have tried it. It causes purple light error, the switch can't turn on although I have tried many times, double check the connections. It works properly when I solder to 2 cmd and clk origin points, I wonder whyYes, left of the resistor is CMD.
And I go back to the same problem of waiting 60 days for the DAT0 adapter or the flex to arrive. I think that at the end of everything I will have to play the TOK on my V1 until the mosfet and the DAT0 adapter arriveah okay well then u need to make it fit somehow.
no oled u need a adapter or u need to take the emmc out the emmc ,reball emmc , set permanent dat0 adapter
then get a bga 153 stencil, solderpast, hotair station , the mosfets and install perm dat0 reball emmc .And I go back to the same problem of waiting 60 days for the DAT0 adapter or the flex to arrive. I think that at the end of everything I will have to play the TOK on my V1 until the mosfet and the DAT0 adapter arrive
Of course not, I waited until I was done like a normal personWTH, did you go outside just to touch grass while you were in the middle of a switch mod?!
The test point in between the RAM and WiFi shieldswhere are you getting the 3.3v from???
Helder had it shared on OSHPark for a little while but I think he took it downWhich site did you get the expansion board from?
Or (gosh) buy the game, rather than steal it? Then you can play wherever you want.then get a bga 153 stencil, solderpast, hotair station , the mosfets and install perm dat0 reball emmc .
install the mosfets to apu then u dont have to wait 60 days
Or (gosh) buy the game, rather than steal it? Then you can play wherever you want.
well most of us use it for homebrew apps, android or linux not everyone does it just for piracy reasons. all game i have installed i bought so.Or (gosh) buy the game, rather than steal it? Then you can play wherever you want.
soooooo how did cutting the pico work out for u this time XdI was so consumed with the multimeter reading that I didn't bother to try it out. Thank you! It did work. I have officially glitched a Switch with a MOSFET.
View attachment 366994
Now on to my next challenge. I bought this big grinder to cut the pico precisely. This is exciting.
View attachment 366995
You need to use both points. Here are some photos.guys why some of you wires transistor to two resistors? and someone to only one
btw can someone send a good quality photo of v2 motherboard solder points?
Also, I would suggest you take the 3.3v from this point.tysm
Hello, yesterday I asked about whether it was possible to use a v2 Flex in a v1, I saw this image on the internet of what I want to do but opposite, a v1 Flex in a V2 and I wanted to ask, how do you think I should do the installation ? the top side of the v1 smd on the right side of the Flex V2 and the bottom side of the v1 smd on the left side of the Flex v2? Or would I have to do it the other way around?