Hacking Hardware Picofly - a HWFLY switch modchip

[simone95]

Up. Anyone know if I have to replace the caps and if i can use the pi-zero`s one.

I've find out they are resistors, can someone measure their resistance?

 

[FreeLander]

since its runing fine now with the 2 caps stollen from the rp go ahead and reinstall the pico with the caps on it should work

I was so consumed with the multimeter reading that I didn't bother to try it out. Thank you! It did work. I have officially glitched a Switch with a MOSFET.

Now on to my next challenge. I bought this big grinder to cut the pico precisely. This is exciting.

 

[Dee87]

I was so consumed with the multimeter reading that I didn't bother to try it out. Thank you! It did work. I have officially glitched a Switch with a MOSFET.

View attachment 366994

Now on to my next challenge. I bought this big grinder to cut the pico precisely. This is exciting.

View attachment 366995

Bevor u start cutting check the aio thread for the pinout and cutting lines

 

[nico77]

HELP!!!
tasukette!!!

recently im trying to remove my micro sd on lite slot...
i think my micro sd stuck ...
but the switch still read the micro sd when i turn it on...


does it bounce back when we press the micro sd???
when i press the micro sd... it feel hard and nothing bounce ??

 

[Hayato213]

HELP!!!
tasukette!!!

recently im trying to remove my micro sd on lite slot...
i think my micro sd stuck ...
but the switch still read the micro sd when i turn it on...


does it bounce back when we press the micro sd???
when i press the micro sd... it feel hard and nothing bounce ??
View attachment 366997

Eject spring might be broken.

 

[nico77]

Eject spring might be broken.

thats what im afraid

i havent eject the micro sd>
since the first time i bought the micro sd.

today im try to eject it... and
wut de.... it doesnt eject

 

[QuiTim]

I was so consumed with the multimeter reading that I didn't bother to try it out. Thank you! It did work. I have officially glitched a Switch with a MOSFET.

View attachment 366994

Now on to my next challenge. I bought this big grinder to cut the pico precisely. This is exciting.

View attachment 366995

Congratulations man, you had an exiting week

 

[moemomeo]

Yes, left of the resistor is CMD.

Thank you for your help! I have tried it. It causes purple light error, the switch can't turn on although I have tried many times, double check the connections. It works properly when I solder to 2 cmd and clk origin points, I wonder why

 

[Chonay]

ah okay well then u need to make it fit somehow.
no oled u need a adapter or u need to take the emmc out the emmc ,reball emmc , set permanent dat0 adapter

And I go back to the same problem of waiting 60 days for the DAT0 adapter or the flex to arrive. I think that at the end of everything I will have to play the TOK on my V1 until the mosfet and the DAT0 adapter arrive

 

[Dee87]

And I go back to the same problem of waiting 60 days for the DAT0 adapter or the flex to arrive. I think that at the end of everything I will have to play the TOK on my V1 until the mosfet and the DAT0 adapter arrive

then get a bga 153 stencil, solderpast, hotair station , the mosfets and install perm dat0 reball emmc .
install the mosfets to apu then u dont have to wait 60 days

 

[snake2]

WTH, did you go outside just to touch grass while you were in the middle of a switch mod?!

Of course not, I waited until I was done like a normal person

where are you getting the 3.3v from???

The test point in between the RAM and WiFi shields

Which site did you get the expansion board from?

Helder had it shared on OSHPark for a little while but I think he took it down

 

[eseldiem]

then get a bga 153 stencil, solderpast, hotair station , the mosfets and install perm dat0 reball emmc .
install the mosfets to apu then u dont have to wait 60 days

Or (gosh) buy the game, rather than steal it? Then you can play wherever you want.

 

[sionka]

guys why some of you wires transistor to two resistors? and someone to only one
btw can someone send a good quality photo of v2 motherboard solder points?

 

[LogicalMadness]

Or (gosh) buy the game, rather than steal it? Then you can play wherever you want.

*Woosh*

Huh? He's trying to advise someone on how to possibly not wait a long time for parts. The fk you on about? O.o

Piracy opinions are pretty worthless in this thread too XD

 

[Dee87]

Or (gosh) buy the game, rather than steal it? Then you can play wherever you want.

well most of us use it for homebrew apps, android or linux not everyone does it just for piracy reasons. all game i have installed i bought so.

Post automatically merged: Apr 25, 2023

I was so consumed with the multimeter reading that I didn't bother to try it out. Thank you! It did work. I have officially glitched a Switch with a MOSFET.

View attachment 366994

Now on to my next challenge. I bought this big grinder to cut the pico precisely. This is exciting.

View attachment 366995

soooooo how did cutting the pico work out for u this time Xd

 

[QuiTim]

guys why some of you wires transistor to two resistors? and someone to only one
btw can someone send a good quality photo of v2 motherboard solder points?

You need to use both points. Here are some photos.

 

[sionka]

You need to use both points. Here are some photos.

tysm

 

[QuiTim]

tysm

Also, I would suggest you take the 3.3v from this point.
It depends on your soldering skills, but I had some trouble trying to solder to the original 3.3v (top of the capacitor). I almost damaged the cap, so i used the one on the emmc board.

 

[SorataVP69]

Hello, yesterday I asked about whether it was possible to use a v2 Flex in a v1, I saw this image on the internet of what I want to do but opposite, a v1 Flex in a V2 and I wanted to ask, how do you think I should do the installation ? the top side of the v1 smd on the right side of the Flex V2 and the bottom side of the v1 smd on the left side of the Flex v2? Or would I have to do it the other way around?

 

[some1ne]

Hello, yesterday I asked about whether it was possible to use a v2 Flex in a v1, I saw this image on the internet of what I want to do but opposite, a v1 Flex in a V2 and I wanted to ask, how do you think I should do the installation ? the top side of the v1 smd on the right side of the Flex V2 and the bottom side of the v1 smd on the left side of the Flex v2? Or would I have to do it the other way around?

Where did you find this? I need to to this (V1 flex on a V2) but I’m not sure the diagram is right.