Hacking WIP [Trinket] [Rebug] [Others] SWITCHBOOT_UF2 / FUSEE_UF2 modchip software

[mattytrog]

Thank you so much. Since this is an external dongle I should treat it as method 1 correct? Pin 1 is my switch I will need to connect to ground to toggle payload? Looking at the files I'm not 100% sure what uf2is considered for the external install I don't think I need swiftboot since of how it's installed but there is a rebug legacy and generic. I think I ruled out the method 3 file since it's method 1?

Yes correct. Just have a play with the different files.
The generic dongle version has payload increase, mode increase and vol+ broken out. Can`t remember which is which now lol

 

[Deleted member 482547]

Yes correct. Just have a play with the different files.
The generic dongle version has payload increase, mode increase and vol+ broken out. Can`t remember which is which now lol

Thanks for the help. I have the files setup now. Parts should be here soon. It looks like the writeup and changelog don't match so what I was thinking of as mode 3 (8 payloads selectable) is now mode 2.

 

[mattytrog]

Thanks for the help. I have the files setup now. Parts should be here soon. It looks like the writeup and changelog don't match so what I was thinking of as mode 3 (8 payloads selectable) is now mode 2.

Probably. I`ve messed that up no doubt.

 

[TheSearch]

The chip isn`t meant to respond.

I think we have our wires crossed here!

The "disable chip" feature will NOT enable a normal boot. To enable a normal boot, or go from normal boot & dual-boot to permanent CFW boot, you need to download the correct UF2 bootloader. Go to my GIT and download a "switchboot part 1" file.

I`m in the process of updating the OP.

Hello,

have tried this now, with both boot loaders Part 1

but unfortunately without success ...

would it be an option to simply enable it in the current Trinket_Legacy_Method3?

 

[Deleted member 482547]

Probably. I`ve messed that up no doubt.

I got it working with the legacy option. Can you explain a little about how its loading the payloads from sd? Is there a way to load the payloads into the UF2 or the internal storage instead of chainloading (assuming that is whats happening)?

 

[B3nnyb0y1990]

Just a little confused. Updated to v1. I press power and it boots into the standard Hekate. I checked and i have no payload.bin on my SD card. If I turn on and hold volume down at the same time then it boots into switchboot Hekate. I have joycon and volume straps. Been checking for a while and I'm possibly just being silly but hope someone can help.

 

[mattytrog]

Just a little confused. Updated to v1. I press power and it boots into the standard Hekate. I checked and i have no payload.bin on my SD card. If I turn on and hold volume down at the same time then it boots into switchboot Hekate. I have joycon and volume straps. Been checking for a while and I'm possibly just being silly but hope someone can help.

You have an update.bin in your bootloader folder.

Delete this, or download v1 bin file from my git and rename to update.bin. however you shouldn't need to

 

[MeteK]

I've installed the modchip(trinket m0) with only joycon and usb strap and now I am not able to update trinket m0's software as it does not recognize it after double pressing reset button. I am on software 0.9.9r41, can someone help me

Same version, same prob here....

Impossible to get it back in explorer .....

 

[mattytrog]

Same version, same prob here....

Impossible to get it back in explorer .....

Disconnect from PC
Is the LED red on the trinket? After pressing RESET twice?
If so, plug in. SWITCHBOOT should pop right up.

--------------------- MERGED ---------------------------

Disconnect from PC
Is the LED red on the trinket? After pressing RESET twice?
If so, plug in. SWITCHBOOT should pop right up.

OK...
I have recreated the problem...

I think it is v7.0.1 firmware or Sept maybe (?) where the problem lies.

Best thing to do, is boot into Hekate / Switchboot, double-press reset... Plug in. Nothing will happen.

Now, boot using your preferred option in the menu. As soon as Horizon frees the port, SWITCHBOOT will pop up.

Nothing I have done! This is not the code!

 

[peteruk]

Is the problem in all the earlier uf2 softwares with 7.0.1 or just these latest versions you've released ?

I was thinking about updating to 7.0.1 but not if there are conflicts

Thanks

 

[mattytrog]

Is the problem in all the earlier uf2 softwares with 7.0.1 or just these latest versions you've released ?

I was thinking about updating to 7.0.1 but not if there are conflicts

Thanks

Nope. Nothing to do with my code. This is a 7.0.1 / sept thing.

 

[peteruk]

Nope. Nothing to do with my code. This is a 7.0.1 / sept thing.

I know it's not the code mate... Sorry, what I'm asking is are there clashes with sept with older versions of the boot software or just your latest releases?

Thanks

 

[mattytrog]

Actually... Fuck it...

New option coming in v1.1 where you can update your chip while booted into Switchboot.

Will be labelled something like "Disable USB for UF2 update"

--------------------- MERGED ---------------------------

I know it's not the code mate... Sorry, what I'm asking is are there clashes with sept with older versions of the boot software or just your latest releases?

Thanks

All versions since Sept / 7.0.1 by the looks of it.

Works fine when booted into 6.2.0.

 

[peteruk]

Thank you for clarification mate, I'll hold off until everything is working in harmony again then make the update

Your work on these projects is massively underrated and your patient attitude is second to none. I am so glad to know you and make use of your talents.

 

[mattytrog]

Thank you for clarification mate, I'll hold off until everything is working in harmony again then make the update

Your work on these projects is massively underrated and your patient attitude is second to none. I am so glad to know you and make use of your talents.

Well thank you for the encouragement!

Keeps me out of the loony bin I suppose.
lunatic asylum
Mental illness treatment centre
Fkin political correctness

 

[josete2k]

Well, you always can boot to OFW if you don't care about burn efuses...

Maybe the AMS powerdown code is making "something" that affects to switboot bootloader.

 

[peteruk]

Has anybody tested the new sxos which supports 7.0.1 and doesn't use sept ?

I could then update and use sxos wirhoiw issue

 

[mattytrog]

Not tested it. I`m working on a solution don`t worry

 

[josete2k]

Has anybody tested the new sxos which supports 7.0.1 and doesn't use sept ?

I could then update and use sxos wirhoiw issue

Me, but not the reset chip under SXOS because I have dualboot and I always use OFW for modchip updates.

RCM-X86 (SWITWBOOT 1.0) only joycon (dualboot)

Sysnand 7.0.1 officially upgraded
Emunand (hidden partition) 6.2.0 upgraded to 7.0.1 (exFAT) via ChoidujourNX

Playing with Dragon Ball FighterZ 1.14 and SSBU 2.0.1

 

[popy]

Has anybody tested the new sxos which supports 7.0.1 and doesn't use sept ?

I could then update and use sxos wirhoiw issue

Also want to know. Did you already tried? Currently using rather old 0.9.6 UF2 on 6.2.0 with sxos 2.5.3. Also want to update [emoji6]

Gesendet von meinem ONEPLUS A6013 mit Tapatalk