Hello Guys,
I'm new here to the forum and just purchased a 1st gen Jailbroken switch (Hetake 5.1.1). The previous owner provided me with a clean NAND backup including BOOT 0/1 that was made on FW 4.1.0 (I checked dumping the syskeys and using FVI.py). Now I'm up to the point were I wish to restore the Sysnand to default and clean to then setup a dual profile to run CFW and OFW alongside each other to be able to play online and enjoy all the jailbreak stuff. (The switch has never been online since it has used CFW).
I've been checking multiple forum posts and can conclude the following;
- I can run a restore through Hekate and restore my clean Nand backup that runs on FW 4.1.0.
- Once the restore is complete, I can boot into OFW using hekate.
- I should be able to then update the 4.1.0 sysnand to match my burnt fuse count (8) version 6.2.0 using ChoiDujourNX
- Once the above has been done my Nintendo is back to 'stock'.
I'm not sure how I'm able to update my clean nand backup to FW 6.2.0 once it has been restored to my Sysnand since I have 8 fuses busted, can you guys help me out?
*edit*
*I just run a nand backup of my currently installed firmware for the hacked state of my switch and it says it's on version 9.1.0.
Firmware version found: 9.1.0 (no exFAT)
Most recent boot: 1980-01-01 00:00:00
Checking the SD of my that my CFW runs on and the fact that ChoiDujourNX is on that sais SD, I assume that the previous owner updated to FW 9.1.0 using ChoiDujourNX. I do not think this influences my initial question, but to be sure I decided to provide this information as well. I do not think it changes anything to my initial question.*
The guides I've managed to find on my own;
Updating/Downgrading Manually switch homebrew guide
Then the next step would be setting up CFW alongside my OFW, a topic of which I'm completely in the dark at this time.
If you guys could help out that would be great!
I'm new here to the forum and just purchased a 1st gen Jailbroken switch (Hetake 5.1.1). The previous owner provided me with a clean NAND backup including BOOT 0/1 that was made on FW 4.1.0 (I checked dumping the syskeys and using FVI.py). Now I'm up to the point were I wish to restore the Sysnand to default and clean to then setup a dual profile to run CFW and OFW alongside each other to be able to play online and enjoy all the jailbreak stuff. (The switch has never been online since it has used CFW).
I've been checking multiple forum posts and can conclude the following;
- I can run a restore through Hekate and restore my clean Nand backup that runs on FW 4.1.0.
- Once the restore is complete, I can boot into OFW using hekate.
- I should be able to then update the 4.1.0 sysnand to match my burnt fuse count (8) version 6.2.0 using ChoiDujourNX
- Once the above has been done my Nintendo is back to 'stock'.
I'm not sure how I'm able to update my clean nand backup to FW 6.2.0 once it has been restored to my Sysnand since I have 8 fuses busted, can you guys help me out?
*edit*
*I just run a nand backup of my currently installed firmware for the hacked state of my switch and it says it's on version 9.1.0.
Firmware version found: 9.1.0 (no exFAT)
Most recent boot: 1980-01-01 00:00:00
Checking the SD of my that my CFW runs on and the fact that ChoiDujourNX is on that sais SD, I assume that the previous owner updated to FW 9.1.0 using ChoiDujourNX. I do not think this influences my initial question, but to be sure I decided to provide this information as well. I do not think it changes anything to my initial question.*
The guides I've managed to find on my own;
Updating/Downgrading Manually switch homebrew guide
Then the next step would be setting up CFW alongside my OFW, a topic of which I'm completely in the dark at this time.
If you guys could help out that would be great!
Last edited by b2theram,