So as i earlier said for me it's blue then white (I'm a little colourblind so i might be wrong), Clk, cpuView attachment 372451View attachment 372452View attachment 372453View attachment 372454View attachment 372455View attachment 372456
View attachment 372457View attachment 372458
the pinout is still the same , u cant get alot closer to them.most of them are right infront of the rp2040View attachment 372459
Hi everyone, i am installing on my lite, i just wonder why we put pico on top of mmc, it seem fit quite good, place it ontop of ram require cut the shield, and i want to keep it intact as much as posible. Anyone who put in on here can help me with then pinout closest with it?
yep, most of them are close, but for gnd and 3.3v, I think there are plenty of pin that I could make a good routing, gnd is easy to get, but I can find 3.3, so if you have another point of 3.3v, please let me knowthe pinout is still the same , u cant get alot closer to them.most of them are right infront of the rp2040
0.1mm will not work the Cpu Mosfet but for mosfet gate 0.1mm will work fine. Use 0.2mm or 0.25mm or 0.3mm For the mosfet. For other points CLk, CMD, Dat0 and RST 0.1mm will be fine but using 0.2mm will also be fine.Does the wire the cpu cable need to be thick or it can be 0,1mm magnet wire?
I don't really think the problem is with the SD because it works with my other hacked Switch. I don't use exfat so I don't that's the problem either. I'll just ask for a refund and buy anotherIf it recognizes one card then the problem should not be with the card reader.
It might be the case that you are missing the exfat drivers but i dont think that it should matter in this stage.
Also, the number of fake Lexar cards is the highest in the market, so you might just have a bad card
I flashed it earlier today and it blinked green for me. I didn't need to bridge the jumper beforeQuick one regarding Firmware 2.72. Does this mean when flashing the RP2040-Zero after dropping the .uf2 file, I don't have to permanently bridge the RGB jumper if the LED flashes Green? Or will it not flash green anymore? Thanks.
I meant cpu flex cable sorry. The 0.1 should be fine right?0.1mm will not work the Cpu Mosfet but for mosfet gate 0.1mm will work fine. Use 0.2mm or 0.25mm or 0.3mm For the mosfet. For other points CLk, CMD, Dat0 and RST 0.1mm will be fine but using 0.2mm will also be fine.
hello,but for update using the toolbox the chip must be installed in the switch right?? cant update the chips in the pc anymore like previous chips then??got the same board. also cant update via the usb. updated via picofly toolbox
thanks for answwer,yes is purple screen BUT right now the console dont turn on at all so right now is black screen,now we already change the resistor,turn on 2 times in purple screen but not anymore,now blak screen,i very very worried because is a brand new console ;.(Ahhh ur talking about purple screen I understood purple led.
Purple screen is cmd resistor issue , recheck connection if everything is fine check the resistor if its damaged it is a 4,7k resistor.
Purple screen will be fixed after fixing cmd resitor
4th in a row. Take your time bro don't rush it. My point is that if your are soldering a wire why you are not using a solder mask. Use solder mask next time so your wire will not roam around in your switch.And here's a fourth kill . OLED installation gives purple color, and doesn't turn on when the modchip is removed. While installing I accidentally removed the 3v3 pad. Could that be the reason?
View attachment 372433
0.1mm will work fine for the flex cable. Btw 0.1mm wire is easy to handle than thicker wire.I meant cpu flex cable sorry. The 0.1 should be fine right?
Hmm weird. I always had to jump mine before but I'm sure the whole jumping rgb process was so that debugging would be easier however now that its changed to long and slow pulses, I'm going to skip the jump because now it's only 3 colours: blue (glitching), white (flashing), yellow (error code). Unless....the yellow upon the initial uf2 flash was an error code!?I flashed it earlier today and it blinked green for me. I didn't need to bridge the jumper before
Alright. One more thing. What repuatble buyer you recommend to getting good flex cable? I was thinking of getting these from Sugergoo through 1866.disconnect battery and check with the USB pulls when u try to turn it on. 0.47 is def charging.
nothing just use mosfets :-)Alright. One more thing. What repuatble buyer you recommend to getting good flex cable? I was thinking of getting these from Sugergoo through 1866.
https://www.sugargoo.com/#/home/pro...?spm=a26352.23326140a26352.0.0.75911e62EjYHcm
What do you think?
right now we remote the chip and flex at all,the console dont turn on,just 2 times get purple screenif you use DAT0 adapter, it could shift a little, shorting neighbour pins
probably you insert the flat cable in opposite direction, you can probe USB lines right to the rp2040 pins with multimeter to ensure the pinout is correct
check ur cmd resistor if its soldered on properly if it is solders properly replace it its 4,7kright now we remote the chip and flex at all,the console dont turn on,just 2 times get purple screen
Thank you !!!!You can't use ANY other but you can use SOME....
I tried. Worked once on a v2 but Got 3 blue screens on Lites and OLEDs. I just have to face the fact that I don't possess the required skills for MOSFETs.nothing just use mosfets :-)
Just route it outside of the shield. That's what I do to all non-OLED models. like so:View attachment 372459
Hi everyone, i am installing on my lite, i just wonder why we put pico on top of mmc, it seem fit quite good, place it ontop of ram require cut the shield, and i want to keep it intact as much as posible. Anyone who put in on here can help me with the pinout closest with it? , Pinout on the pdf tut quite far from here. for eg, the 3.3v