Oled Kamikaze dat0 error *=* no emmc block 0

[nuage83]

Hello everyone



I wanted to test the kamikaze method on an Oled Switch and I got the code *=*



Here are the measurements on the point dat0 0.511 0.620



I'll give you a photo of the suicide bomber I committed.



If anyone can give me an idea



THANKS

 

[jkyoho]

Does it still boot to OFW?

 

[JonJaded]

What did you use to peel the layers away? Everyone I've seen used a fine tip abbrasive pen and rubbing alcohol...

 

[nuage83]

Des it still boot to OFW?

No. before using the kamikaze method I used the adapter but it didn't work as it should. So I did the kamikaze method and since then the console no longer starts at all with a black screen ofw.

 

[psycho-neon]

pls isolate the ground layers. You are shorting the dat0 line to ground. i hope no further damage is done.

 

[mathew77]

@nuage83
They don't call it the Kamikaze method for nothing you know...

 

[nuage83]

thanks for all reply, the mortherboard is dead.

 

[BigOnYa]

thanks for all reply, the mortherboard is dead.

Mail it to @Viktorsilva , he has fixed a few kamikaze screw ups like this already. I'd PM him about it atleast.

 

[Danid]

The same thing happened to me, any solution? Apart from reaching the 4th layer which it shouldn't, in the third layer where the data is, part of it gives me its value but in the other part it is short.
I think I have cut the dat 0 line, as I see that point on dat 0 reaches a point on the ram?

 

[Danid]

finally you can discard this oled, uni layer 3 and 4, the 3 I had to scratch a little more inside until I managed to see it, I made a bridge between the 3 and the 4 and took the dat 0 towards picofly, everything perfect, it starts so much emunand like sysnand.

 

[JonJaded]

finally you can discard this oled, uni layer 3 and 4, the 3 I had to scratch a little more inside until I managed to see it, I made a bridge between the 3 and the 4 and took the dat 0 towards picofly, everything perfect, it starts so much emunand like sysnand.

Would've loved to see a final picture, or atleast how it looks now with it installed.

 

[shahrul910]

finally you can discard this oled, uni layer 3 and 4, the 3 I had to scratch a little more inside until I managed to see it, I made a bridge between the 3 and the 4 and took the dat 0 towards picofly, everything perfect, it starts so much emunand like sysnand.

have you fix it? please can help me .my issues same as you .after drill kamikaze .im test to turn on normally. but fail..all black screen.

Post automatically merged: Apr 1, 2024

finally you can discard this oled, uni layer 3 and 4, the 3 I had to scratch a little more inside until I managed to see it, I made a bridge between the 3 and the 4 and took the dat 0 towards picofly, everything perfect, it starts so much emunand like sysnand.

have you fix it? please can help me .my issues same as you .after drill kamikaze .im test to turn on normally. but fail..all black screen.

 

[Danid]

attached image to see

 

[s4n0suk3]

attached image to see

Hi can you attach a image of your fix, i have same problem, after drilling switch black screen i think i cut the line

 

[Danid]

Hola, ¿puedes adjuntar una imagen de tu solución? Tengo el mismo problema. Después de perforar la pantalla negra del interruptor, creo que corté la línea.

No tengo imagen, lo siento, ten en cuenta que si la has cortado y tienes el pad de 3ª capa o 4ª capa, puedes unirlo ya que es la misma.
Puedes raspar más hacia el blindaje y encontrarás el Dat 0.

I don't have an image, I'm sorry, note that if you have cut it and you have the 3rd layer or 4th layer pad, you can join it since it is the same.
You can scrape further towards the shield and you will find the dat 0 line