Hi all, I’m trying to install a new picofly RP2040 into my oled switch as the one that was originally installed by someone else ended up failing however when booting the switch I get blue Long green short green indicating a DAT0 error however my DAT0 solder adapter reads in the range of .500~.850 (I think it’s .753 if I remember correctly) still getting this error though any suggestions?
OLED getting D0 error but I have correct diode voltage
- Thread starter HunterCustom
- Start date
- Views 1,310
- Replies 13
what resistors did you use on the picofly? A lot of people had to double up the 47ohm, or use a 100ohm, on both dat0 and CMD. Then again, if you just went and did that first, then maybe you want to try the 47ohm route...
I don’t have any that im aware of im just using what was included I have one of those PCB ones but I’ll look into grabbing the 47ohm resistor see if that helps
yea, the exact model is needed. If you bought an instinct v6s, for instance, that is NOT a picofly, and doesn't require resistors. If it IS a picofly, did you read through the .pdf picofly install guide from this page?
Hey guys sorry, Naming threw me off. I have an instinct v6 clone version such as this image
this is my DAT0 connector, and I still get the long short error
Here is a clip of the error code (incase Im reading it wrong as i've done before)
update before i go to bed can confirm diode of .516, tried soldering direct to chip no long same error considering order nonclone chip to try
Post automatically merged:
this is my DAT0 connector, and I still get the long short error
Post automatically merged:
Here is a clip of the error code (incase Im reading it wrong as i've done before)
Post automatically merged:
update before i go to bed can confirm diode of .516, tried soldering direct to chip no long same error considering order nonclone chip to try
Last edited by HunterCustom,
It's likely not a resistor issue with that chip, but I have no experience with that chip. Does it accept firmware from https://github.com/Ansem-SoD/Picofly/tree/main/Firmwares ? It's not something that's listed in the readme, but I'm going to jump the gun and assume that there's no way a real instinct chip firmware is going to work right on that thing. Your DAT0 looks as solid as it can be.
Did it come with firmware update instructions? Where do you download the firmware from?
EDIT: WAtch this video starting around 16:30, then see if maybe you have the same issue with grounding:
Did it come with firmware update instructions? Where do you download the firmware from?
EDIT: WAtch this video starting around 16:30, then see if maybe you have the same issue with grounding:
Last edited by urherenow,
I’ve had luck with these on the v1/2 and LITEs but never the oled and I’ve always used the firmware from your provided link. I’ll definitely check out the video you included though see if that would help. But I did end up ordering an instinct off Ali Express last night might as well throw a real one onto at this point.
Thank you for your help with this issue
I was wondering if you have any updates with the Instinct installed. I have the same exact problem although it does work occasionally but sometimes fails. I can't order the instincts directly to Germany so i'd have to use an expensive reship service to geth them here. I'd get 5-10 chips st once to make it worth the cost, but i'd need to know if these fixed your problem.
When it doesn't glitch i get the dat0 error. The ribbon cant move a bit, it's a new v6 one and i have resoldered again today, hope that improves it. And i hope we can soon get instincts in Germany, the 50% premium over the picoflys are well worth it imo of they work better. I am using a cheap knockoff picofly btw.
Your Dat adapter is very Loose. Even if its working now, there is a high chance that one of this days it will stop glitching. You need to improve your anchors. You didn´t even solder the right and left ones.I hate those Dat addapters. I allways use Kamikase mod because on every 10 consoles, 2 or 3 will have to come back from costumer because they stop glitching.
Similar threads
-
-
@
SylverReZ:
@Jayro, I don't see whats so special about the DS ML, its just a DS lite in a phat shell. At least the phat model had louder speakers, whereas the lite has a much better screen.+1 -
@
SylverReZ:
They probably said "Hey, why not we combine the two together and make a 'new' DS to sell".
-
-
-
@
Veho:
Nothing special about it other than it's more comfortable than the Lite+1
for people with beefy hands. -
-
-
-
-
-
-
@
The Real Jdbye:
@SylverReZ if you could find a v5 DS ML you would have the best of both worlds since the v5 units had the same backlight brightness levels as the DS Lite unlockable with flashme -
-
-
@
BigOnYa:
A woman with no arms and no legs was sitting on a beach. A man comes along and the woman says, "I've never been hugged before." So the man feels bad and hugs her. She says "Well i've also never been kissed before." So he gives her a kiss on the cheek. She says "Well I've also never been fucked before." So the man picks her up, and throws her in the ocean and says "Now you're fucked."+1 -
-
-
@
BakerMan:
anyways, we need to re-normalize physical media+1
if i didn't want my games to be permanent, then i'd rent them -
@
BigOnYa:
Agreed, that why I try to buy all my games on disc, Xbox anyways. Switch games (which I pirate tbh) don't matter much, I stay offline 24/7 anyways.
-
-
@
cearp:
@BakerMan - you can still "own" digital media, arguably easier and better than physical since you can make copies and backups, as much as you like.
The issue is DRM -
@
cearp:
You can buy drm free games / music / ebooks, and if you keep backups of your data (like documents and family photos etc), then you shouldn't lose the game. but with a disk, your toddler could put it in the toaster and there goes your $60
-
-
@
rqkaiju2:
i like physical media because it actually feels like you own it. thats why i plan on burning music to cds
