Emu nand help!

Discussion in 'Wii - Hacking' started by Fudge, Aug 21, 2012.

Aug 21, 2012

Emu nand help! by Fudge at 3:05 PM (1,096 Views / 0 Likes) 8 replies

  1. Fudge
    OP

    Banned Fudge Remember that death is not the end, but only a tra

    Joined:
    Aug 26, 2009
    Messages:
    2,655
    Location:
    New York
    Country:
    United States
    I have Mighty Channels running at the moment, however it's compatibility isn't what I hoped for, so I want to set up Neek. I ran the ModMii setup, but now I'm lost. I already I have a nand built, I just odn't know how to use Neek. Like, what do I install on my Wii?? I'm usually good with this stuff but this time I'm stumped. Please help!
     
  2. XFlak

    Member XFlak Wiitired but still kicking

    Joined:
    Sep 12, 2009
    Messages:
    9,122
    Location:
    Ontario
    Country:
    Canada
    ModMii would have told u what to do... you probably clicked finished or closed ModMii without reading the instructions.

    Anyways, install the neek WAD, then launch the neek channel. Alternatively, u can rename the bootneek folder on your sd card to bootmii then just launch bootmii via the HBC or boot2.
     
  3. Fudge
    OP

    Banned Fudge Remember that death is not the end, but only a tra

    Joined:
    Aug 26, 2009
    Messages:
    2,655
    Location:
    New York
    Country:
    United States
    I installed the neek wad, but I get a stack dump. Does it matter if my NAND is a bootmii dump??
     
  4. XFlak

    Member XFlak Wiitired but still kicking

    Joined:
    Sep 12, 2009
    Messages:
    9,122
    Location:
    Ontario
    Country:
    Canada
    When exactly do u get a stack dump and what devices do u have connected to your Wii when it happens? Are you trying to run uneek+di, sneek+di, uneek, or sneek? Are you trying the original neek or neek2o?

    Some people have had success using their nand dump's as their emunands, I personally have never gotten it to work without a lot of tweaking (actually my first attempt I needed giantpune's help). On the other hand, I've always been able to get ModMii's fresh emunands to work perfectly. Other people have reported the exact opposite experience though. So if one doesn't work for you, try the other. And if you're real wii's nand dump is giving you problems, try removing the HBC from it (using showmiiwads), or u can try removing priiloader from it (using ModMii's emunand modifier).
     
  5. Fudge
    OP

    Banned Fudge Remember that death is not the end, but only a tra

    Joined:
    Aug 26, 2009
    Messages:
    2,655
    Location:
    New York
    Country:
    United States
    Got it working, put in my Wii's serial number and online is working too. I have a few questions. Is there any wiinertag support?? Also, is it normal to have long load times for the Wii Menu?
     
  6. XFlak

    Member XFlak Wiitired but still kicking

    Joined:
    Sep 12, 2009
    Messages:
    9,122
    Location:
    Ontario
    Country:
    Canada
    wiinnertag, not sure

    long load times, it depends on the emunand device you're using, if u got a fast HDD or SD load times are faster. Also, the more channels u have on your wii menu the longer it will take to load. To counter this, people often have their emunand set to autoboot to joyflow or postloader.
     
  7. Fudge
    OP

    Banned Fudge Remember that death is not the end, but only a tra

    Joined:
    Aug 26, 2009
    Messages:
    2,655
    Location:
    New York
    Country:
    United States
    Which brings me to my next question. Postloader doesn't boot for me, is there any reason for this?? Also, what is joyflow?? I have heard of it but don't know what it does. Thanks man.
     
  8. XFlak

    Member XFlak Wiitired but still kicking

    Joined:
    Sep 12, 2009
    Messages:
    9,122
    Location:
    Ontario
    Country:
    Canada
    re postloader, you should post that question in the postloader thread. But how are u trying to load it? If using uneek, u should have the app saved to the sd card, if using sneek, u should have it saved to a USB. I believe uneek can also load apps from USB (not 100% sure though), but generally speaking whatever device you're using to run your nand it cannot be used for anything else (with the exception than loading wii games in the case of uneek+di). Alternatively u could install postloader to your emunand as priiloader's installed file, or u could inject it into a channel\wad and install that to your emunand.

    About joyflow, it's a mod of wiiflow designed to run in a neek environment. It's very much like postloader, but with better graphics and less functions.
     
  9. Fudge
    OP

    Banned Fudge Remember that death is not the end, but only a tra

    Joined:
    Aug 26, 2009
    Messages:
    2,655
    Location:
    New York
    Country:
    United States
    That's why, I run everything off USB right now, didn't know it was a forwader. Thanks.
     
    1 person likes this.

Share This Page