dumped max media dock eeprom

Discussion in 'NDS - Flashcarts and Accessories' started by stuntpenguin007, Apr 13, 2009.

Apr 13, 2009
  1. stuntpenguin007
    OP

    Newcomer stuntpenguin007 Newbie

    Joined:
    Dec 19, 2008
    Messages:
    9
    Country:
    United States
  2. Nitto

    Newcomer Nitto Member

    Joined:
    Apr 12, 2009
    Messages:
    14
    Location:
    Canada eh?
    Country:
    Canada
    I must sound like a retard, but were did you get instructions for the eeprom reader. Also: What IC chips were their? (skylite)

    (Time to check instructables)
     
  3. stuntpenguin007
    OP

    Newcomer stuntpenguin007 Newbie

    Joined:
    Dec 19, 2008
    Messages:
    9
    Country:
    United States
    I used the same design as the xbox eeprom reader (because I had to use it on my xbox anyways)
    http://forums.afterdawn.com/thread_view.cfm/357863
    just 2 4k resistors, a serial port and 2 zener diodes

    I used pin 8 or at least the eigth pin from the left on the cf card reader as a ground and put it in my ds and turned it on to supply power.

    as for what ICs... other than the eeprom there is one major ic thing on there but it's mostly faded out on the front but heres what I can make out.

    QY7C683008 56PVXC
    B 04PRI 0619
    CYP 634051

    thats probably not completely right but close.



    Edit: judging by my google results its probably a CY7C68300B-56PVXC
     
  4. Nitto

    Newcomer Nitto Member

    Joined:
    Apr 12, 2009
    Messages:
    14
    Location:
    Canada eh?
    Country:
    Canada
    I had made my own eeprom one for my 360. It's called a unicorn.
    If you don't mind could you please take a picture of the guts?
     
  5. UltraMagnus

    Member UltraMagnus hic sunt dracones

    Joined:
    Aug 2, 2007
    Messages:
    1,967
    Location:
    Portsmouth
    Country:
    United Kingdom
    that is a usb to PATA chip , I guess the MMD uses it to communicate with the CF card.
     
  6. stuntpenguin007
    OP

    Newcomer stuntpenguin007 Newbie

    Joined:
    Dec 19, 2008
    Messages:
    9
    Country:
    United States
  7. Nitto

    Newcomer Nitto Member

    Joined:
    Apr 12, 2009
    Messages:
    14
    Location:
    Canada eh?
    Country:
    Canada
    I know that =), just a little google =).

    Thanks for the pic =)

    And thanks for supporting my firmware project, if you want to help more you can go to: http://gbatemp.net/index.php?showtopic=147...p;#entry1898930
     
  8. SifJar

    Member SifJar Not a pirate

    Joined:
    Apr 4, 2009
    Messages:
    6,022
    Country:
    United Kingdom
    so is there anything useful to be done with this dumped eeprom? perhaps enable the max media dock to run in gba mode and use gba homebrew? please dont flame me if thats stupid, im not too good with this kind of thing
     
  9. Nitto

    Newcomer Nitto Member

    Joined:
    Apr 12, 2009
    Messages:
    14
    Location:
    Canada eh?
    Country:
    Canada
    In a xbox eeprom you could get the key for a drive =)
     
  10. KazoWAR

    Member KazoWAR GBAtemp Advanced Maniac

    Joined:
    Aug 12, 2008
    Messages:
    1,749
    Location:
    Winter Haven
    Country:
    United States
    I really dont understand, this is just the MMD sav file right? totaly useless?
     
  11. stuntpenguin007
    OP

    Newcomer stuntpenguin007 Newbie

    Joined:
    Dec 19, 2008
    Messages:
    9
    Country:
    United States
    useless... maybe

    but it's not a sav file. when put in a hex editor you can make out a few words like datel and some others I can't remember. I don't know where they show up. Probably when you plug it into your pc via usb.

    that means this is probably the mmd firmware.
     
  12. UltraMagnus

    Member UltraMagnus hic sunt dracones

    Joined:
    Aug 2, 2007
    Messages:
    1,967
    Location:
    Portsmouth
    Country:
    United Kingdom
    well, I guess you need to run it through a disassembler, maybe an ARM disassembler.
     
  13. stuntpenguin007
    OP

    Newcomer stuntpenguin007 Newbie

    Joined:
    Dec 19, 2008
    Messages:
    9
    Country:
    United States
    OK I'll look into that... although I'm not sure why I would want to.
     

Share This Page