Hello,
I got my d2pro 9 wire yesterday and installed today, but it doesn't work after installation. The problems is: DVD drive like doing step movement, when the drive take in disc, it move inch by inch, and after the disc is in the position, it doesn't spin. Only the red LED on d2pro is light up, it never flash. and the green LED never light up.
I tried to upgrade the d2pro to latest firmware, seems can't. Below is the screen output for my upgrade process, you can see after the 1st time success flash, the current firmware version still be 0.9b.
Is my chip faulty? Any suggestion?
=============================================
C:\Documents and Settings\xxx\Desktop>d2prog
d2pro 9w updater v1.0
Programmer firmware: v1.0
Searching for chip: A3P125 detected.
Current firmware: "d2pro (9 wires)" (v0.9b)
Available firmwares:
Product FPGA SPI
================== ==== ====
1) "d2pro (9 wires)" v1.0 v1.0
Using firmware "d2pro (9 wires)", v1.0.
WARNING!
If you have connected the programmer to anything else
than a d2pro chip, it may be rendered useless.
To start flashing, type 'yes': yes
Erase FPGA [.]
Flash FPGA [.........................]
Verify FPGA [.........................]
Erase SPI [.]
Flash SPI [.........................]
Verify SPI [.........................]
Done! Spent 87.9 seconds.
C:\Documents and Settings\xxx\Desktop>d2prog
d2pro 9w updater v1.0
Programmer firmware: v1.0
Searching for chip: A3P125 detected.
Current firmware: "d2pro (9 wires)" (v0.9b)
Available firmwares:
Product FPGA SPI
================== ==== ====
1) "d2pro (9 wires)" v1.0 v1.0
Using firmware "d2pro (9 wires)", v1.0.
WARNING!
If you have connected the programmer to anything else
than a d2pro chip, it may be rendered useless.
To start flashing, type 'yes': no
Process aborted!
I got my d2pro 9 wire yesterday and installed today, but it doesn't work after installation. The problems is: DVD drive like doing step movement, when the drive take in disc, it move inch by inch, and after the disc is in the position, it doesn't spin. Only the red LED on d2pro is light up, it never flash. and the green LED never light up.
I tried to upgrade the d2pro to latest firmware, seems can't. Below is the screen output for my upgrade process, you can see after the 1st time success flash, the current firmware version still be 0.9b.
Is my chip faulty? Any suggestion?
=============================================
C:\Documents and Settings\xxx\Desktop>d2prog
d2pro 9w updater v1.0
Programmer firmware: v1.0
Searching for chip: A3P125 detected.
Current firmware: "d2pro (9 wires)" (v0.9b)
Available firmwares:
Product FPGA SPI
================== ==== ====
1) "d2pro (9 wires)" v1.0 v1.0
Using firmware "d2pro (9 wires)", v1.0.
WARNING!
If you have connected the programmer to anything else
than a d2pro chip, it may be rendered useless.
To start flashing, type 'yes': yes
Erase FPGA [.]
Flash FPGA [.........................]
Verify FPGA [.........................]
Erase SPI [.]
Flash SPI [.........................]
Verify SPI [.........................]
Done! Spent 87.9 seconds.
C:\Documents and Settings\xxx\Desktop>d2prog
d2pro 9w updater v1.0
Programmer firmware: v1.0
Searching for chip: A3P125 detected.
Current firmware: "d2pro (9 wires)" (v0.9b)
Available firmwares:
Product FPGA SPI
================== ==== ====
1) "d2pro (9 wires)" v1.0 v1.0
Using firmware "d2pro (9 wires)", v1.0.
WARNING!
If you have connected the programmer to anything else
than a d2pro chip, it may be rendered useless.
To start flashing, type 'yes': no
Process aborted!