Attachments
You can't install nsp update using choidujournx
Maybe using an nsp installer like tinfoil or goldleaf
If you absolutly want to use choidujournx, you have to search nca file on google
Sx site or darth site
I can't give you a link, it is not allowed
Maybe using an nsp installer like tinfoil or goldleaf
If you absolutly want to use choidujournx, you have to search nca file on google
Sx site or darth site
I can't give you a link, it is not allowed
Figured out the issue was with Mac you got to run following sudo chflags -R arch /Volumes/NAME OF SD/Firmware9.1.0
Firmware installed succesffuly it had autoRCM enabled. When it reboot i got a blank screen.
I connected SX Pro and disabled AutoRCM and could get into OFW, however I am unable to load CFW, when i go into SX Pro OS and select Custom Firmware it loads blank screen.
Any solution on this?
I know this is such a noob question but I never dealt with this but what is "archive bits" and what do the fix in hekate do?
It’s just a file attribute, In Windows it’s used for identifying if a file should be backed up whenever it’s changed or something like that (and it can be set/unset by checking/unchecking the “ready for archiving” option in the properties of a file)
On Switch, FS has this thing where if you name a bunch of split parts of a file “00”, “01”, etc and throw them in a folder then set the archive bit on them (or the folder, don’t remember which) it’ll treat those split files as a single file with the file name being the name of the folder they’re in. It can cause some fucky stuff to happen though.
Last edited by ZachyCatGames,
I managed to update to 9.1.0 with choidujournx but my issue now is when I boot to CFW nothing loads blank screen. I can access OFW through SX OS. I’m running SX Pro dongle on 2.9.2
any help on this?
Hello,
I installed the last version of kosmos nx with es / fs patches I am currently on the frimware 10.0.0.1 and I would like to go to 10.0.0.2 in order to correct the pad problems. when I launch the intalization of the latest ChoiDuJour nx firmware hangs at step 1/6 "Testing for BIS protection.
I wanted downgrade to 9.2.0 same problem.
Can you help me please.
I installed the last version of kosmos nx with es / fs patches I am currently on the frimware 10.0.0.1 and I would like to go to 10.0.0.2 in order to correct the pad problems. when I launch the intalization of the latest ChoiDuJour nx firmware hangs at step 1/6 "Testing for BIS protection.
I wanted downgrade to 9.2.0 same problem.
Can you help me please.
@Masana I had the same problem as you, you HAVE to use title redirection (hold R) to launch hbmenu in order for choidujournx to work properly.
Do not use nro2nsp to launch hbmenu or choidujournx will crash.
Do not use nro2nsp to launch hbmenu or choidujournx will crash.
So I fixed the initial issue, problem was with SX2.9.5 boot.dat, I placed boot.dat 2.9.2 and it loads the CFW.
Ive never used archive with hekate and files larger than 4GB have worked perfectly fine previously.
My issue just gets worse, non of the backup Gs work errors like 2002-3999 appear now. I have ran my emunand 8.1.0 to start again but still get get backup Gs to work without crashing on me. I formatted the SD card also before putting emunand back on.
Ive never used archive with hekate and files larger than 4GB have worked perfectly fine previously.
My issue just gets worse, non of the backup Gs work errors like 2002-3999 appear now. I have ran my emunand 8.1.0 to start again but still get get backup Gs to work without crashing on me. I formatted the SD card also before putting emunand back on.
Hey all, I'm trying to update my 9.2.0 to 10.0.2 but ChoiDujourNX keeps crashing when I tell it to install.
I'm on Atmosphere 0.12.0 and firmware 9.2.0.
Any help would be appreciated.
http://imgur.com/vJxZdzJ
I'm on Atmosphere 0.12.0 and firmware 9.2.0.
Any help would be appreciated.
http://imgur.com/vJxZdzJ
Try running it on Applet Mode if you are running ChoidujourNX on full ram mode.
Similar threads
-
BigOnYa
-
Xdqwerty
what are you looking at? -
Psionic Roshambo
-
AncientBoi
-
-
-
-
@
BigOnYa:
If your internet speeds are fast enough. Streaming 4k takes alot. I used to only have 20mb sec, and 4k struggled. Now I have 300mb sec and 4k plays fine.+1
-
-
-
-
-
-
-
@
Psionic Roshambo:
I think Game streaming should work like this.... Local Hardware able the run the game fine, game engine and common assets stored locally, all FMV and music and textures could be streaming+1
-
-
@
Xdqwerty:
also @BigOnYa im making some progress on my gdevelop project, implemented various mechanics
-
-
@
BigOnYa:
Or free government supplied high speed internet be nice also. Like Obama care. Xdqwerty that's cool, its time consuming but rewarding once done or playable, to see what you've made from scratch. Animations take forever, but worth it.+1
-
-
-
@
Xdqwerty:
@BigOnYa,+1
and the visual aspect of the game is quite crude (the sprite that looks best is that of the protagonist just because he is a stickman with sunglasses) -
@
BigOnYa:
There is a bullets behaviour you assign to your character, that makes the code easier, under "behaviours"
-
-
@
Xdqwerty:
i meant that when the character is pointing to the right, the bullets spawn where they should, but when he is on the right, they move to the right but the spawn point is incorrect
-
@
BigOnYa:
Itch.io has lots of free assets also. Under the bullets behavior tab, there is a "rotate bullets" option, can try that. Or in the code can try
- fire bullet Player.X(PlayerDirection) -
-
-
@
BigOnYa:
That's cool tho, I'm proud of you going back to it, not giving up. It is difficult at first to learn, but fun once you get the hang of it. I think I've watched every tutorial video there is, but I still struggle sometimes to get stuff to work right. But gotta keep trying dif things, and eventually you will get it right.+1
them