Hacking WIP [Trinket] [Rebug] [Others] SWITCHBOOT_UF2 / FUSEE_UF2 modchip software

[mattytrog]

What if I am wanting to use a trinket M0 as a dongle? what bootloader/etc should i flash?

Use any of the dongle ones. Or I'll make a generic one

 

[reminon]

Use any of the dongle ones. Or I'll make a generic one

Would you mind making a generic one for me?

 

[mattytrog]

Would you mind making a generic one for me?

OK... Check OP in 20 minutes

 

[reminon]

OK... Check OP in 20 minutes

ok. thank you sir!

 

[mattytrog]

ok. thank you sir!

Check post 2 under dongle section of downloads. One of those suitable?

 

[reminon]

Check post 2 under dongle section of downloads. One of those suitable?

which bootloader should i use with them?

 

[mattytrog]

which bootloader should i use with them?

With a dongle? None. The dongle is only for newly fitted internal chips.

 

[reminon]

With a dongle? None. The dongle is only for newly fitted internal chips.

Stays at the rcm black screen for both. I'm using a standard trinket m0, with a 3v battery pack soldered to "bat" and "gnd". From the usb female port on the trinket, I'm using a microusb to usb c cable that I made "data lines only". Also, i had already flashed a bootloader before i contacted you, I don't know if that matters as I've flashed the generic uf2's since then.

 

[mattytrog]

Stays at the rcm black screen for both. I'm using a standard trinket m0, with a 3v battery pack soldered to "bat" and "gnd". From the usb female port on the trinket, I'm using a microusb to usb c cable that I made "data lines only". Also, i had already flashed a bootloader before i contacted you, I don't know if that matters as I've flashed the generic uf2's since then.

Try ejecting SD card and try again

 

[mattytrog]

Try ejecting SD card and try again

Also, data lines only you say? You need a GND connection too...

 

[reminon]

Also, data lines only you say? You need a GND connection too...

Ahh. Ok, I'll try it when I get home. Thanks.

--------------------- MERGED ---------------------------

Also, data lines only you say? You need a GND connection too...

I don't know how i missed the gnd wire. thank you it works.

 

[link42586]

So I am sitting back on 5.1.0 with oldschool hekate 2.3 or something like that on my dongle (the one that came out when atmosphere patches was first leaked) and plan on updating all this stuff/firmware to play newer games as once those patches dropped I never needed anything else cept now to play newer games. So um this seems way complicated compared to the other thread idk what's going on. Anyways need newest hekate 4.0 whatever UF2 files for trinket m0 dongle..Off the shelf nothing done to it other than some header pins so I can connect A battery to it easy. So is this what I want?

• Generic Trinket with capacitive mode & payload buttons / pads

 

[mattytrog]

So I am sitting back on 5.1.0 with oldschool hekate 2.3 or something like that on my dongle (the one that came out when atmosphere patches was first leaked) and plan on updating all this stuff/firmware to play newer games as once those patches dropped I never needed anything else cept now to play newer games. So um this seems way complicated compared to the other thread idk what's going on. Anyways need newest hekate 4.0 whatever UF2 files for trinket m0 dongle..Off the shelf nothing done to it other than some header pins so I can connect A battery to it easy. So is this what I want?

• Generic Trinket with capacitive mode & payload buttons / pads

Use the one with no buttons. Then put your payload on SD root. Rename to payload.bin and you are away.

 

[mattytrog]

Seriously... Is this all to complicated? I didn't think it could get simpler than dragging a uf2 and renaming your payload to "payload.bin".

Oh well...

 

[Koksi__]

@mattytrog
Thank you for your hard work.
It is really great project.

I think you should clarify that we have to flash 2x uf2 files to work correctly (It may also be that I am too stupid )

 

[mattytrog]

@mattytrog
Thank you for your hard work.
It is really great project.

I think you should clarify that we have to flash 2x uf2 files to work correctly (It may also be that I am too stupid )

Added a note to OP. I`ve called it Step 0. In yellow near the top.

 

[Gismor]

v0.9.2 added to post 2. Only small changelog.

Method 3 version Tested and works perfect thanks =)

 

[link42586]

Added a note to OP. I`ve called it Step 0. In yellow near the top.

I've been hacking systems since the original xbox and everything since. The thing is. Once reinx released patches that allowed backups that was all I needed till now. But I need A newer firmware and all that for newer games so that prompted me to update all this stuff. Now having said that if you have been following the scene closely which I haven't it would be A great guide i'm sure. But since I had no reason to look into anything at all till now it's like I have to learn everything all over again and the scene has moved very fast. But thx for the info.

Btw back in the day I knew everything their is to know about hacking an xbox....Just got one the other day and it's like learning to hack it all over again. No modchip this time but man. It's alot to take in. Like the switch scene.

 

[neff123]

Hello Matty, is the R4s working? I tried to apply R4S_v092_Simple-UF2.UF2 to my dongle but after loading it on dongle, it just keeps on flashing red led. What am i doing wrong?

 

[mattytrog]

Hello Matty, is the R4s working? I tried to apply R4S_v092_Simple-UF2.UF2 to my dongle but after loading it on dongle, it just keeps on flashing red led. What am i doing wrong?

I thought it was. Looks like I have my answer.

Would it be possible for someone to take some nice clear pics of both sides of the board? I just cannot find one clear enough. I thought I had implemented their code correctly. Obviously not.

PLEASE PLEASE ANYBODY!!! As big as possible.

--------------------- MERGED ---------------------------

The LED should flash. The code in my UF2 is different to the original one. It should flash, you plug it in, it sends, then LED goes off...

There is nothing special about their board from what I can tell. My UF2 should work...

 

[Shadow_The_Hedgehog82]

I've got mine installed in this configuration what should i do? Also if anyone wasn't aware you can use your switch as a dongle for other switches with a c to c cable

I'm curious if anyone has tried to install a modchip/dongle inside the dock and used auto rcm? I know some people that do not use their switch in portable mode & thought this would be a good idea for them.

It may not work as the data lines are used when the console is charging. If you try to boot with a modchip while the charger is plugged in it doesn't work so i doubt the dock will