Homebrew Now I'm confused. A9LH downgrade part.

[xZaggin]

sup guys, for the past 3 days I've been trying none stop to downgrade to 2.1.0

No luck, it always failed at NFIRM. (~15 min in)
After more than 50 attempts I decided instead of rebooting, I'll just go in system settings.

Now I see that it says Rei 2.1.0-4E?

I reboot once more going back to emunand and it's just a black screen, repeat the same process same outcome. NFIRM FAIL > Home Button > Settings > 2.1.0 > Reboot > Black screen.

So what exactly am I experiencing here?

 

[Deleted member 373223]

no cfw can boot 2.1

 

[Ridge]

Just to make sure, you're trying to downgrade the Emu/RedNAND, right?

 

[xZaggin]

no cfw can boot 2.1

Yes I am aware, but in this case I'm wondering is it because of the firmware being broken or because it just can't run either way

Just to make sure, you're trying to downgrade the Emu/RedNAND, right?

Yes, Emunand...if I had tried to downgrade anything else for 50 times I would've been fucked since the first try

 

[Deleted member 373223]

Yes I am aware, but in this case I'm wondering is it because of the firmware being broken or because it just can't run either way



Yes, Emunand...if I had tried to downgrade anything else for 50 times I would've been fucked since the first try

well, are you downgrading from a 10.7 emunand?

 

[xZaggin]

well, are you downgrading from a 10.7 emunand?

Yes I am, Rei 10.7

 

[Deleted member 373223]

Yes I am, Rei 10.7

try with AuReinand instead

 

[xZaggin]

try with AuReinand instead

How would I go about replacing reinand to AuReinand? In fact I only thought AuReinand was after a9lh

 

[Deleted member 373223]

How would I go about replacing reinand to AuReinand? In fact I only thought AuReinand was after a9lh

what made you tohught that? even plailect guide suggest aureinand. aureinand works just fine with menuhax

 

[Ridge]

Yes I am aware, but in this case I'm wondering is it because of the firmware being broken or because it just can't run either way



Yes, Emunand...if I had tried to downgrade anything else for 50 times I would've been fucked since the first try

Right, you would. And you're following Plailect's guide I assume? I also noticed you're using Rei EmuNAND, which the guide doesn't use, and I don't know if it matters. All the necessary steps before downgrading to 2.1 is injecting FBI to Health & Safety and then formatting twice before installing PlaiSysUpdater. All on EmuNAND. Your EmuNAND WILL brick then, it's supposed to happen. You're sure you did this 100%?

 

[The Real Jdbye]

sup guys, for the past 3 days I've been trying none stop to downgrade to 2.1.0

No luck, it always failed at NFIRM. (~15 min in)
After more than 50 attempts I decided instead of rebooting, I'll just go in system settings.

Now I see that it says Rei 2.1.0-4E?

I reboot once more going back to emunand and it's just a black screen, repeat the same process same outcome. NFIRM FAIL > Home Button > Settings > 2.1.0 > Reboot > Black screen.

So what exactly am I experiencing here?

Set up CakesFW according to the guide and use it for the 2.1 downgrade. You can change back to Rei/AuRei when you're done with OTP.

 

[xZaggin]

Right, you would. And you're following Plailect's guide I assume? I also noticed you're using Rei EmuNAND, which the guide doesn't use, and I don't know if it matters. All the necessary steps before downgrading to 2.1 is injecting FBI to Health & Safety and then formatting twice before installing PlaiSysUpdater. All on EmuNAND. Your EmuNAND WILL brick then, it's supposed to happen. You're sure you did this 100%?

Yes I started from step 4, created emunand backups (original and formatted) + sysnand backup.
I have FBI, I formatted it twice and installed PlaiSys. I am aware that it's supposed to brick.

My question is why do I still get the NFIRM FAIL at the very end, yet if I home button my way out of it, it shows I'm on Rei 2.1.0

what made you thought that? even plailect guide suggest aureinand. aureinand works just fine with menuhax

I'll try it out and see how that goes

 

[xZaggin]

Yes I started from step 4, created emunand backups (original and formatted) + sysnand backup.
I have FBI, I formatted it twice and installed PlaiSys. I am aware that it's supposed to brick.

My question is why do I still get the NFIRM FAIL at the very end, yet if I home button my way out of it, it shows I'm on Rei 2.1.0



I'll try it out and see how that goes

After a couple attempts I got AuRei to boot, Now I'm gonna test it out

edit: It Worked!

 

[The Real Jdbye]

Yes I started from step 4, created emunand backups (original and formatted) + sysnand backup.
I have FBI, I formatted it twice and installed PlaiSys. I am aware that it's supposed to brick.

My question is why do I still get the NFIRM FAIL at the very end, yet if I home button my way out of it, it shows I'm on Rei 2.1.0



I'll try it out and see how that goes

It's probably your CFW blocking FIRM installs, that's why I suggested setting up Cakes (it has FIRM install blocking as an option but the guide instructs you to leave it disabled)

 

[xZaggin]

It's probably your CFW blocking FIRM installs, that's why I suggested setting up Cakes (it has FIRM install blocking as an option but the guide instructs you to leave it disabled)

it worked on the first try with AuRei, I wasted 3 days of trying nonstop. Thanks guys!