Switch OLED missing the CMD capacitor

[mvmiranda]

Hello!
I have a Switch OLED someone else tried to perform a modchip install and knocked off the CMD resistor in the process.



He didn't try to turn the board on when he noticed he removed the res.
Does anyone happen to know the resistor value?

Thanks!

 

[BigOnYa]

You can try posting here also.
https://gbatemp.net/threads/compone...stly-the-motherboard-and-main-console.525026/
or
https://gbatemp.net/threads/switch-oled-teardown-v1-v2.600550/

 

[sean222]

That resistor is 3.5Kohm. I knocked it off myself and lost it. sthetix got the value for me from his working board.

Edit: Apparently it's 4.7Kohm instead?

 

[mvmiranda]

That resistor is 3.5Kohm. I knocked it off myself and lost it. sthetix got the value for me from his working board.

Meanwhile I received another OLED and while I was doing the mod I measured the resistor.
Found a similar value on an old 3DS board and harvested it

Thx for the information, though!

Cheers!

 

[sean222]

Meanwhile I received another OLED and while I was doing the mod I measured the resistor.
Found a similar value on an old 3DS board and harvested it

Thx for the information, though!

Cheers!

Nice!

 

[heinrich_frei]

Hello! I need help to identify the missing capacitor near emmc. Switch Oled. Would somebody be so kind to measure the capacitor from their own switch if possible.

 

[kerelenko]

Hello!
I have a Switch OLED someone else tried to perform a modchip install and knocked off the CMD resistor in the process.

View attachment 286972

He didn't try to turn the board on when he noticed he removed the res.
Does anyone happen to know the resistor value?

Thanks!

My I know the value of the one beside the command? I knock that one on mine

 

[kerelenko]

That resistor is 3.5Kohm. I knocked it off myself and lost it. sthetix got the value for me from his working board.

Where can I buy these components? I knocked the one beside the cmd. Do you know it's value?

 

[mvmiranda]

My I know the value of the one beside the command? I knock that one on mine

Where can I buy these components? I knocked the one beside the cmd. Do you know it's value?

I saw you saw this resistor value in the other thread.
It's 0201 47kOhms. I'd say you can find it online. Try Aliexpress.
Good luck!

 

[KaiN69420]

So I knocked my CMD one too, I still have it, but is there a special trick to reattaching it? Also do I have any other options or am I SoL? I looked for the 0201 online in case I need a new one and I see 3.48 KOhms and 3.57 KOhms, not sure which one would be correct, I am looking on mouser, if that helps. Any help would be extremely appreciated.

 

[doom95]

How did you knock it off? If you soldered a wire to it and pulled on that to take off the resistor, then that side of the resistor is probably no longer able to be soldered to. Otherwise, just flux and heat..

 

[doom95]

Also, the value is 4.7k, you should definitely find that in any sample book.

 

[kerelenko]

The resistor that is sitting on the CMD point is 4k7 ohm and the one beside that is 47k ohm.
You need steady hands, a microscope, and a fine tip soldering iron with good flux to solder it back. Hot air would be better.

I also knocked the 47k ohm resistor and realized my hands are not as steady at it used to be. The CLK point was especially troublesome. So I sent it to @de9ed to fix it and finish the mod.

 

[kerelenko]

I saw you saw this resistor value in the other thread.
It's 0201 47kOhms. I'd say you can find it online. Try Aliexpress.
Good luck!

Bought a 0207 sampler from Amazon for $70.
This mod taught me a lot and my total cost is close to $1600 already. Tools, equipment, shipping, chip, taxes, Switch, etc.

 

[doom95]

Then again there's probably no other mod that you cannot do anymore, so definitely a sensible investment
Or am I the only one rationalizing like this?

 

[KaiN69420]

How did you knock it off? If you soldered a wire to it and pulled on that to take off the resistor, then that side of the resistor is probably no longer able to be soldered to. Otherwise, just flux and heat..

When I was trying to apply solder to the top part for the CMD, I guess I used the wrong tip and heated the resistor and it came off. I still have it, but it’s super hard trying to get it to line up with the pads and keep the pads heated

 

[KaiN69420]

The resistor that is sitting on the CMD point is 4k7 ohm and the one beside that is 47k ohm.
You need steady hands, a microscope, and a fine tip soldering iron with good flux to solder it back. Hot air would be better.

I also knocked the 47k ohm resistor and realized my hands are not as steady at it used to be. The CLK point was especially troublesome. So I sent it to @de9ed to fix it and finish the mod.

Is de9ed in US? I found a guy in TX, reviews look legit, it’s Wayayeo anyone know them?

 

[doom95]

He's an excellent guy, you can let him work on your stuff with full trust

 

[KaiN69420]

He's an excellent guy, you can let him work on your stuff with full trust

Awesome thank you so much, yea looks like he has been around for a long time, has good Google reviews and seen him mentioned on scene sites

 

[kerelenko]

Is de9ed in US? I found a guy in TX, reviews look legit, it’s Wayayeo anyone know them?

Vancouver.