Toggle sidebar

Hacking SWITCH NOOB PARADISE - Ask questions here

  • Thread starter Thread starter APartOfMe
  • Start date Start date
  • Views Views 6,259,606
  • Replies Replies 48,066
  • Likes Likes 66
Hey, i want to attempt modding the switch lite with a picofly modchip. I am however unsure of what tools i need to do this and whether or not this is feasible for someone who doesn't have any experience with soldering besides soldering a few wires together.

Currently i have a cheap soldering iron which temperature can be set to approximately 330c and above. Is a more advanced soldering iron with better temperature control required?
I have seen some people suggest that a microscope is needed. Is this true and would a magnifying glass be enough?
Since i don't really have any experience with soldering i will need to practice before doing the actual installation. What would be the best way to do this? Should i use a practice board from Aliexpress and in that case which type?

If anyone could help me with these questions it would be greatly appreciated :)
 
does the switch v1 have the cmd resistor? if not so, what are some causes for a purple screen brick
 
Looking for guide to remove all traces of sxos. Was given a switch that I believe is not not patched or updated from very old firmware. I'm not familiar with much switch hacking. Any help would be appreciated
 
smuddge said:
Looking for guide to remove all traces of sxos. Was given a switch that I believe is not not patched or updated from very old firmware. I'm not familiar with much switch hacking. Any help would be appreciated
Click to expand...

Some info would help, does it says emunand when you open the album?
 
Hi guys, I have 2 basic questions. I have a modded brand-new switch lite which I haven't done anything on yet. Basically, I'm at the 'No SD Card' screen for PicoFly. Anyway, since it's brand new the OFW is at v12.0.0 so it's really old. Can I update OFW normally before setting up my SD card with atmosphere and etc. ?

Also, should I download a free game from nintendo eshop for title takeover?

I'd appreaciate any help. Thanks.
 
zGamer said:
Hi guys, I have 2 basic questions. I have a modded brand-new switch lite which I haven't done anything on yet. Basically, I'm at the 'No SD Card' screen for PicoFly. Anyway, since it's brand new the OFW is at v12.0.0 so it's really old. Can I update OFW normally before setting up my SD card with atmosphere and etc. ?

Also, should I download a free game from nintendo eshop for title takeover?

I'd appreaciate any help. Thanks.
Click to expand...

Do you know if it have a clean ofw?
 
  • Like
Reactions: Blythe93
Hayato213 said:
Do you know if it have a clean ofw?
Click to expand...
Yes, it is. I'm the first owner of the device. Only got professional help for the chip installation, didn't touch anything on software side yet because I just wanted to ask here first before doing anything to prevent a potential ban.
 
  • Like
Reactions: Blythe93
zGamer said:
Yes, it is. I'm the first owner of the device. Only got professional help for the chip installation, didn't touch anything on software side yet because I just wanted to ask here first before doing anything to prevent a potential ban.
Click to expand...

If you want to play online on ofw then create an emunand for your homebrew and pirated games. Use Nintendo server to do OFW update, and do a NAND backup with Hekate.
Post automatically merged:

zGamer said:
Hi guys, I have 2 basic questions. I have a modded brand-new switch lite which I haven't done anything on yet. Basically, I'm at the 'No SD Card' screen for PicoFly. Anyway, since it's brand new the OFW is at v12.0.0 so it's really old. Can I update OFW normally before setting up my SD card with atmosphere and etc. ?

Also, should I download a free game from nintendo eshop for title takeover?

I'd appreaciate any help. Thanks.
Click to expand...

As for what to do for title override, use album in emunand to enter applet mode and install the homebrew menu nsp, it is out there look for it. Don't install any nsp on your sysnand as it share nand with ofw
 
  • Like
Reactions: Blythe93 and zGamer
Hayato213 said:
You can probably just wait it out, when you get the sd card , h2testw the card, you need the sd card for hekate to do a full nand backup.
Click to expand...
Oh, I actually have an SD card. I was asking that since I haven't installed anything on the device, should I just update OFW on stock mode. Will that cause any bans if only the chip is installed? If not, should install the Atmosphere for v12.0.0 since that's preinstalled out of the box. I got a bit confused because the device doesn't even have a Nintendo account yet and switch.hacks.guide says you will need a free game for the title take over.

Sorry for noob questions though, just curious.
 
  • Like
Reactions: Blythe93
zGamer said:
Oh, I actually have an SD card. I was asking that since I haven't installed anything on the device, should I just update OFW on stock mode. Will that cause any bans if only the chip is installed? If not, should install the Atmosphere for v12.0.0 since that's preinstalled out of the box. I got a bit confused because the device doesn't even have a Nintendo account yet and switch.hacks.guide says you will need a free game for the title take over.

Sorry for noob questions though, just curious.
Click to expand...

You don't need to download an eshop game to use title override, you can use album to launch applet mode so you can get access to homebrew, what you want to do is install the homebrew menu nsp that is out there so it allow you to launch the homebrew menu in full ram mode, you could also use applet mode to install a game and then use that game to title override but it is kinda obsolete when you can just install homebrew menu nsp.

Anyway you don't want to use that guide it is very outdated

https://web.archive.org/web/20240109162117/Http://rentry.org/SwitchHackingIsEasy

read this one instead.
 
  • Like
Reactions: Blythe93, BigOnYa and zGamer
Hayato213 said:
You don't need to download an eshop game to use title override, you can use album to launch applet mode so you can get access to homebrew, what you want to do is install the homebrew menu nsp that is out there so it allow you to launch the homebrew menu in full ram mode, you could also use applet mode to install a game and then use that game to title override but it is kinda obsolete when you can just install homebrew menu nsp.

Anyway you don't want to use that guide it is very outdated



read this one instead.
Click to expand...
Alright, thank you for the link and your time! :)
 
  • Like
Reactions: Blythe93 and BigOnYa
Hello guys a little question, months ago i installed a game with the jpn region but now its available the usa region with the latest version, theres a way to export the jpn saves to the usa version? I tried with jksv but i have two different games with the same tittle and cant restore them with jksv
 
Fireword said:
Hello guys a little question, months ago i installed a game with the jpn region but now its available the usa region with the latest version, theres a way to export the jpn saves to the usa version? I tried with jksv but i have two different games with the same tittle and cant restore them with jksv
Click to expand...

Backup the Japanese one, inject it to the USA save
 
  • Like
Reactions: Blythe93
Hello.
So iv got this switch that was setup with emunand booting from hecate, but I now need to upgrade it.
Its on system 14.1.2 and ams 1.3.2E.

What would the steps be to make sure I do not corrupt the nand and do this the easiest way? It was installed with clean nand in its day.
 
  • Like
Reactions: Dust2dust and Blythe93
I wanna buy a monolith-type joycon controller, currently looking at DOBE TNS-2163. Is there someone who owns it, so I could get some feedback about its reliability, comfort and quality?
 
My V1 switch seems to be ridiculously slow when loading games. Haven’t really played around with anything nor have I updated the CFW since Mario Wonder came out so not sure what made it get slow. Im using a U1 Sandisk SD card. Would a V3 SD card help? Would it be a case of simply copying and pasting the contents over to the new SD card?
 

Site & Scene News

Go to forum More news

Popular threads in this forum