Hacking Reinstalling Henkaku on Enso 3.65

[the_last_V8]

Well, to put it short I kinda effed up after switching to Enso 3.65. I was in the middle of setting up my SD card as ux0 and instead of copying ux0:tai/ to ur0:tai/ I managed to delete it instead of moving it (a smart move - I know). I could easily restore them if I could run henkaku, but it is no longer possible on my current CFW. Is there a way to get the files that are placed in the tai folder by running the exploit (taihen.skprx, henkaku.suprx, henkaku.skprx) by any other means (like, ex. from someone else)? Without them I a bit screwed - I can run Molecular shell and Vita Shell, but whenever I try to run anything under *Kernel my PS TV enters an endless loop of booting up and powering down. Any help would be greatly appreciated : )

 

[Hayato213]

Think you can press PS button on controller along with R1 to enter recovery mode , where there you can disable all plugins. You should check your config text , that is what causing the loop.

 

[the_last_V8]

I not so much worried about the loop (I have that covered) as about the inability to run anything under Kernel, cause I'm really missing the critical part that is making it run (the above-mentioned files).

 

[aytug25]

Well, to put it short I kinda effed up after switching to Enso 3.65. I was in the middle of setting up my SD card as ux0 and instead of copying ux0:tai/ to ur0:tai/ I managed to delete it instead of moving it (a smart move - I know). I could easily restore them if I could run henkaku, but it is no longer possible on my current CFW. Is there a way to get the files that are placed in the tai folder by running the exploit (taihen.skprx, henkaku.suprx, henkaku.skprx) by any other means (like, ex. from someone else)? Without them I a bit screwed - I can run Molecular shell and Vita Shell, but whenever I try to run anything under *Kernel my PS TV enters an endless loop of booting up and powering down. Any help would be greatly appreciated : )

i can copy and send you my own tai folder so you can replace but i am not at home now and i cant send before 6-7 hours...

 

[Tommy084]

You dont have to restore taihen, the taihen kernel plugin is hardcoded.
From the config.txt
«# henkaku.skprx is hard-coded to load and is not listed here»

I think you are traying to use a plugin not made for 3.65, i also had the loop, i then removed the plugin after holding L while booting. Good luck

https://www.reboot.ms/forum/attachments/config-txt.6527/

 

[the_last_V8]

i can copy and send you my own tai folder so you can replace but i am not at home now and i cant send before 6-7 hours...

Take your time. Cheers : )!

--------------------- MERGED ---------------------------

You dont have to restore taihen, the taihen kernel plugin is hardcoded.
From the config.txt
«# henkaku.skprx is hard-coded to load and is not listed here»

I think you are traying to use a plugin not made for 3.65, i also had the loop, i then removed the plugin after holding L while booting. Good luck

Ok, I will look into that. I am pretty sure the plugins are compatibile but it won't hurt to check this again. Thanks for the tip : )

 

[Tommy084]

Take your time. Cheers : )!

--------------------- MERGED ---------------------------

Here is my backup of tai

 

[the_last_V8]

Here is my backup of tai

Thank you! I'll test this and will let you know if this helps. This will take some time though - I need to get home first. Cheers!

 

[the_last_V8]

Here is my backup of tai

Sir, your help turned out to be invaluable. The backup and the tip on plugin version resolved the kernel and boot problem. I still have some challanges ahead but that is a story for another time ; ).

Cheers!

 

[Tommy084]

Okay, thats good
Uploaded a new zip file with the tai and Henkaku plugins, but its not needed.

 

[PurpleChew]

Okay, thats good
Uploaded a new zip file with the tai and Henkaku plugins, but its not needed.

Thank you Tommy! After hours of headache and searching, you provided exactly what I needed to fix the issue. Thank you so much lol.