Picofly AIO Thread

[A-Hacked-Soul]

RIP this V2 I guess, contacts fell right off.

 

[ypeeLs]

RIP this V2 I guess, contacts fell right off.

ez fix, expose the traces before the pad and solder to that

 

[A-Hacked-Soul]

ez fix, expose the traces before the pad and solder to that

I will look into that. Might be easier

 

[malgamer]

RIP this V2 I guess, contacts fell right off.

direct solder a wire from gate mosfet

 

[swutch]

I accidently soldert D0 to one of these points, and now the Switch do not turn on.
I should have better isolated those points.

Did i destroy my nand?
Or is there any hope it can be fixed?

 

[Flaviocarvalho]

Hi everyone...i recently installed picofly on my switch lite...ibstalled the mosfets...tested and got no sd screen...closed the console and when power on got a yellow/orange light just after blue and loads ofw...can anyone explain where is the problem? (Sorry for my english)

 

[Adran_Marit]

I have an issue with V1 unpached switch.
I can enter in hekate but i get black screen in OFW and Atmosphere.
What is wrong ?

why not RCM if its unpatched?

I accidently soldert D0 to one of these points, and now the Switch do not turn on.
I should have better isolated those points.

Did i destroy my nand?
Or is there any hope it can be fixed?

have you removed the chip and tried bootign normally?

 

[swutch]

why not RCM if its unpatched?


have you removed the chip and tried bootign normally?

Eternal glitching with chip, or no life sign without.

 

[Adran_Marit]

Eternal glitching with chip, or no life sign without.

with the chip removed, please plug the switch into your pc, and check if it is detected in RCM

 

[ojobenito]

Hi.
I might be doing a PicoFly installation this weekend.
I don't see much information about MicroSD preparation. I'm in no way interested in emunand (please avoid replies saying "it's essy and you should do it", I really don't want emunand), so how can I boot directly into Atmosphere and that's it? Where do I put the fusee.bin payload? (Don't want the Hekate menu, just boot Atmosphere directly)
Thanks!

 

[Adran_Marit]

Hi.
I might be doing a PicoFly installation this weekend.
I don't see much information about MicroSD preparation. I'm in no way interested in emunand (please avoid replies saying "it's essy and you should do it", I really don't want emunand), so how can I boot directly into Atmosphere and that's it? Where do I put the fusee.bin payload? (Don't want the Hekate menu, just boot Atmosphere directly)
Thanks!

I highly, HIGHLY advise booting into hekate at least once to do a full nand backup + boot 0/1 + keys.

It works for looking for a payload.bin on the root of your microSD, so in theory all you need to do is download the atmosphere files and renaming fusee.bin to payload.bin.

Worst case scenario, set hekate to autoboot atmosphere with no delay

 

[ojobenito]

Ok, I will do the nand backup.
Is pocofly more dangerous than V1 rcm method and that's why you recommend making the nand backup? I never did nand backup on my other switch because I never did emunand, nor I touched any systen files, overclock, or any mods/overclock/anything.
I always use a MicroSD with Atmosphere, no system mods in any way, and never had a problem.

 

[A-Hacked-Soul]

Ok, I will do the nand backup.
Is pocofly more dangerous than V1 rcm method and that's why you recommend making the nand backup? I never did nand backup on my other switch because I never did emunand, nor I touched any systen files, overclock, or any mods/overclock/anything.
I always use a MicroSD with Atmosphere, no system mods in any way, and never had a problem.

A nand backup is always advised. IN case you mess something up or you get a bad piece of homebrew or a software intended to brick your system. It gives you a way to unbrick the console.

 

[consolex]

Hello
I have a switch lite with sx lite spacecraft
I would like to put a picofly, I think you have to flash the nand before ?

 

[swutch]

with the chip removed, please plug the switch into your pc, and check if it is detected in RCM

Yeay, was able to fix it.
It was the D0 Adapter.
Thanks for your help.

 

[Flaviocarvalho]

Hi everyone...i recently installed picofly on my switch lite...ibstalled the mosfets...tested and got no sd screen...closed the console and when power on got a yellow/orange light just after blue and loads ofw...can anyone explain where is the problem? (Sorry for my english)

Any help please?

 

[NandieeHU]

Any help please?

U had to check your solders joints. May be a cable is shorted to gnd or anything like this.

 

[cicci084]

Hi guys, I don't know if I'm in the right place, if so I apologize and maybe tell me where I can ask.

I have a console with parental controls on.
My question is:
If I install a rp2040 by creating an emuMMC, in this mode would the switch start without parental controls?
Thank you

 

[Flaviocarvalho]

is there any test i can do with the multimeter?

U had to check your solders joints. May be a cable is shorted to gnd or anything like this.

 

[Donnie-Burger]

Hi guys, I don't know if I'm in the right place, if so I apologize and maybe tell me where I can ask.

I have a console with parental controls on.
My question is:
If I install a rp2040 by creating an emuMMC, in this mode would the switch start without parental controls?
Thank you

https://gbatemp.net/threads/reset-parental-control-nx-an-easy-to-reset-the-pin-for-controls.556891/