N3DS XL Nand mod wont write only read

Discussion in '3DS - Console, Accessories and Hardware' started by TariqSoftDev, Aug 28, 2016.

  1. TariqSoftDev
    OP

    TariqSoftDev ~Zexceil

    Member
    3
    Sep 18, 2013
    London
    I recently modded my N3DS XL from a 4-pin JST to a 6-pin MicroJST,All DAT lines except DAT3 is being used, I also notice slow read speeds of about 2.1Mbp/s I should be getting 5.5Mbp/s, Im using a Transcend TS-RDP8K
    3DS wiring

    [​IMG]

    Transcend RDP8K wiring

    [​IMG][​IMG]

    I've checked for any touching wires but none, I get the default Bootrom error 200, each wire is coloured coded for, Black(GND), Red(CLK), Yellow(CMD), Green(DAT0), Blue(DAT1), White(DAT2)
     
    Last edited by TariqSoftDev, Aug 31, 2016
  2. LameNobody

    LameNobody Weighted Companion Cube Enthusiast

    Member
    4
    Jan 23, 2015
    Canada
    127.0.0.1
    Is your makeshift SD missing the lock switch?
    If its missing, it won't push the contacts together in the SD reader and enable writing...

    Also, your pictures are broken... use a different host... like imgur.
     
  3. cravas

    cravas GBAtemp Advanced Fan

    Member
    3
    Jul 30, 2016
    Portugal
    Oeiras
    And I also think that you either use ALL DATs, or only DAT0, don't skip DAT3.

    And, as above, if the small piece is missing, it's the same as being READ only. Put some tape around the FrankenSD to ilude it.
     
  4. TariqSoftDev
    OP

    TariqSoftDev ~Zexceil

    Member
    3
    Sep 18, 2013
    London
    Its soldered directly to the sd card port with a switch to toggle the write, I have fixed this by soldering to the MicroSD port , requires a dud MicroSD to be inserted
     
  5. vb_encryption_vb

    vb_encryption_vb That hardmod guy....

    Member
    7
    Nov 21, 2015
    United States
    Acworth, GA
    You can get 5.5mbs with 4 wires...

    You need the other dat soldered as well if using the 7 wire install. Check your ground.
     
  6. TariqSoftDev
    OP

    TariqSoftDev ~Zexceil

    Member
    3
    Sep 18, 2013
    London
    Im using a 6 wire Micro JST port and could you tell me how to get 5.5Mbp/s with 4 wires?
     
  7. vb_encryption_vb

    vb_encryption_vb That hardmod guy....

    Member
    7
    Nov 21, 2015
    United States
    Acworth, GA
    Clk, cmd, grnd, and dat0
     
  8. TariqSoftDev
    OP

    TariqSoftDev ~Zexceil

    Member
    3
    Sep 18, 2013
    London
    I'll just de solder the Dat1 and Dat2, from the SD card reader, do I have to do it on 3DS side?
     
  9. vb_encryption_vb

    vb_encryption_vb That hardmod guy....

    Member
    7
    Nov 21, 2015
    United States
    Acworth, GA
    Yes
     
  10. gamesquest1

    gamesquest1 Nabnut

    Moderator
    20
    GBAtemp Patron
    gamesquest1 is a Patron of GBAtemp and is helping us stay independent!

    Our Patreon
    Sep 23, 2013
    well you dont have to desolder them,but they will just be doing nothing though
     
  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice