Hardware N3DS NAND backup possible, I hope.

[James310]

Does anyone know how to get pass those hidden screws under the rubber plugs thing, can't find a screw driver that fits

 

[milerwan]

You have to buy the appropriate screwdriver to do it... a cross shaped screwdriver at the right size.

 

[James310]

You have to buy the appropriate screwdriver to do it... a cross shaped screwdriver at the right size.

Little More Specific Please

 

[hellothere1993]

So, do i have to remove my wires to make 3DS bot normally after flashing the mpdified NAND?

 

[James310]

So, do i have to remove my wires to make 3DS bot normally after flashing the mpdified NAND?

if only there directly connected to a sd, if a port then no

 

[hellothere1993]

if only there directly connected to a sd, if a port then no

i have them connected to an SD. The weird thing about it was that i would get the blue screen even when i only had wires connected to the board

 

[Ninoh-FOX]

Hello, I have a question, it's not for me, but to people who have asked me. Is there an alternative CLK to old3DSxl and 2DS? Thank you.

 

[fuyukaidesu]

It seems you put the ribbon above the connector instead of below.
Now the connector should be relaxed because the valve should never be raised.

I suggest you to send your console to a professional for repairing.

Here, I tried to take a better picture. I'm pretty sure the ribbon is touching the pins, I can't see how it is "above" the connector: if I press it while pressing the home button when the 3DS is turned on, it's properly detected.

 

[gamesquest1]

Here, I tried to take a better picture. I'm pretty sure the ribbon is touching the pins, I can't see how it is "above" the connector: if I press it while pressing the home button when the 3DS is turned on, it's properly detected.

you have broken the connectors they are not supposed to be lifted up, from the pictures the tops look like they have been snapped off, you were supposed to just pull the cable out without pulling/lifting anything

only way to go fro here is to replace the ports or trying to wedge them into position or something which i doubt would be very reliable

 

[fuyukaidesu]

they are not supposed to be lifted up

Fuck. I guess replacing them would be very hard?

 

[Ninoh-FOX]

Other question, the wire that I use is: AWG30 P/N DM-30-1000.

Is it ok or is better other?

( is under pressure from the wires on the bottom screen, I can not take off all pressure. Anyway the pressure is minimal, only if I push the screen like Hulk )

 

[James310]

So Does anyone know the screwdriver ima need to open those 2 hidden screws under the rubber plugs

 

[XeroOmega]

So Does anyone know the screwdriver ima need to open those 2 hidden screws under the rubber plugs

for your clarity I use a phillips #00 and i pry out the plug with a fingernail. it's pretty easy, and don't strip your screws.

 

[JacksonS]

I'm having some issues with this mod on on New 3DS XL. Weeks ago I installed a micro USB port in the 3DS and used it to downgrade from 10.4 - it worked. Now, it boots up normally instead of giving me an error message even though it's connected to the SD reader and the reader is plugged in. Does anyone know what this might mean? No wires are loose, I redid everything to make sure. Same result.

 

[James310]

I'm having some issues with this mod on on New 3DS XL. Weeks ago I installed a micro USB port in the 3DS and used it to downgrade from 10.4 - it worked. Now, it boots up normally instead of giving me an error message even though it's connected to the SD reader and the reader is plugged in. Does anyone know what this might mean? No wires are loose, I redid everything to make sure. Same result.

Is it plugged in while it's turning on?

 

[JacksonS]

Is it plugged in while it's turning on?

Yes. If I turn the 3DS on before connecting it to the PC (while connected to the SD reader), I get the error message reading:

 

[James310]

Yes. If I turn the 3DS on before connecting it to the PC (while connected to the SD reader), I get the error message reading:

Then what's the problem?

 

[JacksonS]

Then what's the problem?

That's not the error code I'm looking for. If I plug it into the PC while it's in this state, I still get nothing.

 

[James310]

That's not the error code I'm looking for. If I plug it into the PC while it's in this state, I still get nothing.

People have different error codes , what's the sd card reader your using, if the program can't see it it's always the sd card fault or its reader

 

[JacksonS]

People have different error codes , what's the sd card reader your using

Well the error code I consistently got when it was working ended in "00000200 00000000". I'm using this adapter made by Omega:

It's the exact same one I used before so I'm not sure what this means.