Luma 3DS issue

Discussion in '3DS - Homebrew Development and Emulators' started by TheDeathryder, Apr 7, 2017.

  1. TheDeathryder
    OP

    TheDeathryder Newbie

    Newcomer
    5
    0
    Oct 6, 2016
    United States
    So I had to install a game specific update (Pokemon Moon) and now when I try to load Luma it gets stuck on a black screen. It was working fine immediately before the update. Anyone else have similar issues?
     
  2. rikumax25!

    rikumax25! Keyblade Wielder

    Member
    1,417
    511
    Apr 21, 2016
    Costa Rica
    update your luma arm9loaderhax.bin
     
  3. x65943

    x65943 Resident Greekaboo, Amateur Dog Father

    Member
    2,605
    2,303
    Jun 23, 2014
    United States
    Indiana
  4. Giodude

    Giodude GBAtemp's official rock

    Member
    GBAtemp Patron
    Giodude is a Patron of GBAtemp and is helping us stay independent!

    Our Patreon
    4,235
    1,309
    May 17, 2015
    United States
    New York
    If you use the no outlines patch you have tp update that. Also of you use a firmware.bin you need to delete that.
     
  5. TheDeathryder
    OP

    TheDeathryder Newbie

    Newcomer
    5
    0
    Oct 6, 2016
    United States
    I've been using the most recent version of Luma. Every time I try to boot into Luma from the homebrew launcher, I just get a black screen.
     
  6. x65943

    x65943 Resident Greekaboo, Amateur Dog Father

    Member
    2,605
    2,303
    Jun 23, 2014
    United States
    Indiana
    Boot your 3ds with another sd card with only arm9loaderhax.bin on it, and then swap in your primary sd card.
     
  7. KunoichiZ

    KunoichiZ GBAtemp Guru

    Member
    8,537
    3,600
    Mar 16, 2012
    United States
    If you have a9lh, you don't boot into Luma from the Homebrew Launcher. What is your 3DS setup?
     
    x65943 likes this.
  8. TheDeathryder
    OP

    TheDeathryder Newbie

    Newcomer
    5
    0
    Oct 6, 2016
    United States
  9. Giodude

    Giodude GBAtemp's official rock

    Member
    GBAtemp Patron
    Giodude is a Patron of GBAtemp and is helping us stay independent!

    Our Patreon
    4,235
    1,309
    May 17, 2015
    United States
    New York
    That doesn't help much. Like excision the following:

    Do you use an emunand?
    How do you launch luma3ds?
    What is your sysnand firmware?
     
  10. TheDeathryder
    OP

    TheDeathryder Newbie

    Newcomer
    5
    0
    Oct 6, 2016
    United States
    I do use an emunand, the firmware on the 3ds itself is 9.2.0-20U, I have it set up so that it boots into the homebrew menu where I manually load luma3ds.
     
  11. Giodude

    Giodude GBAtemp's official rock

    Member
    GBAtemp Patron
    Giodude is a Patron of GBAtemp and is helping us stay independent!

    Our Patreon
    4,235
    1,309
    May 17, 2015
    United States
    New York
    Yea.... There's part your problem. It used to be that people would keep on using their emunand because a9lh was dangerous and had a high brick rate if you didn't know what you're doing. Now I'd say the opposite is true, and it's probably safer and easier to install arm9loaderhax at this point. There's virtually no chance of bricking as long as your education exceeds that of a trained toucan. It will eliminate the need of an emunand, save that gb off of your sd card, and firm write protection will protect you from accidentally don't something stupid on sysnand and losing cfw. As many have mentioned before, your best option is to follow 3ds.guide, as it is the most developed and up to date guide yet.
     
    Quantumcat likes this.