Homebrew Question GoldLeaf Errors

[jellybeangreen2]

I have two NSP's which both give me error:0x236e02

Module: FS (2)

Description: invalid PFS0 (NSP) (4535)



Any ideas what the problem could be? - Switch firmware is 5.1.0.

 

[hippy dave]

Bad NSP? If you've verified that they're good, maybe they're too new & 5.1.0 doesn't have the necessary masterkey for them? Did you look in the goldleaf thread for that error number?

 

[XorTroll]

I get the same error for one or two specific NSPs. Probably the NSPs have something which makes them invalid for the console, but what the error says, invalid NSPs.

 

[Deleted User]

I get the same error for one or two specific NSPs. Probably the NSPs have something which makes them invalid for the console, but what the error says, invalid NSPs.

Hi, i was installing some NSP's yesterday through 0.5 GoldLeaf, everything went fine but only 1 issue, the DLC's NSP's where not installed at all, don't know if it only happens to me, (that NSP's sizes were small, like 128 kb)

 

[toxic9]

You have to exit the application and start it again. Then you can install. It's an issue I found some time ago. It happens with tiny dlc's

 

[jellybeangreen2]

I get the same error for one or two specific NSPs. Probably the NSPs have something which makes them invalid for the console, but what the error says, invalid NSPs.

Thanks for replying to my thread @XorTroll - The NSP's are both valid. - obtained from two different sources and the MD5 checks out. - I wonder if it is because I am on 5.1.0? they are genuine and not converted.

Thanks for the other comments guys

 

[XorTroll]

I am on 5.1.0 too

--------------------- MERGED ---------------------------

Hi, i was installing some NSP's yesterday through 0.5 GoldLeaf, everything went fine but only 1 issue, the DLC's NSP's where not installed at all, don't know if it only happens to me, (that NSP's sizes were small, like 128 kb)

Small DLC like Rocket League's one usually is a few KBs FYI

 

[hippy dave]

I get the same error for one or two specific NSPs. Probably the NSPs have something which makes them invalid for the console, but what the error says, invalid NSPs.

Do you get a different error if the nsp needs a higher masterkey than your current fw?

 

[jellybeangreen2]

Do you get a different error if the nsp needs a higher masterkey than your current fw?

This is what I'm wondering. - Currently backing up my Micro SD (256GB) so its going to take an hour! - I will set up EmuNAND and test again.. - I did convert NSP to XCI and change the keygen to 5.x but still didn't work. I do have a feeling it is related to 7.x. Once set up I will reply back.

 

[XorTroll]

Do you get a different error if the nsp needs a higher masterkey than your current fw?

The nsp doesn't store the keygen...? That is what happens with ncas

 

[hippy dave]

The nsp doesn't store the keygen...? That is what happens with ncas

Ok makes sense.

 

[jellybeangreen2]

The nsp doesn't store the keygen...? That is what happens with ncas

I understand the decryption of the NCA with X key. However, when you can change the minimum system version on a certain NSP; why does it ask for the master key? This would give the impression that not all modules are decrypted?

 

[Deleted User]

enough space?

 

[jellybeangreen2]

enough space?

Yep

--------------------- MERGED ---------------------------

To update everyone, I set up emunand. Then updated emunand to 7.0.1. The two NSP installed fine. Goldleaf reports it to be keygen8. Which explains maybe why it couldn’t boot on 5.1.0. - I also tested my converted XCI for 5.1.0, doesn’t work on 5.1.0 but works on 7.0.1. There must be dependancies for 7.x

 

[TerminatR]

Did this ever get resolved?

I have the same issue.

 

[jellybeangreen2]

Did this ever get resolved?

I have the same issue.

goldleaf is the problem unfortunately. A new tool reNXpack is a solution. Or use SXOS emuNAND and install the latest firmware on the emuNAND so you don’t have to patch a game each time

 

[jug5]

Thanks for two working solutions @jellybeangreen2, reNXpack was new to me and solved the problem. Also tried the emunand with $latest and that worked as well.

 

[jellybeangreen2]

Thanks for two working solutions @jellybeangreen2, reNXpack was new to me and solved the problem. Also tried the emunand with $latest and that worked as well.

Glad both solutions worked for you.