Hacking 3DS unbricking progress

[Moquedami]

Where does DAT3 go on the SD adapter?

DAT3 goes on the pin on the right of CMD
( the second counting from right to left)

 

[Habbert]

DAT3 goes on the pin on the right of CMD
( the second counting from right to left)

Ok, thanks.
So triple checking before I solder.
The image below is correct?

 

[krisztian1997]

Where does DAT3 go on the SD adapter?

https://dl.dropboxusercontent.com/u/33926727/3ds/duino.png

 

[Moquedami]

I´m a bit confused myself too.
You appear to have the GND on the same pin than me, but It´s different on Krisztian1997`s schematic

 

[ASUS]

 

[Moquedami]

but that looks just like this and Krisztian1997 said it was wrong

 

[Habbert]

I´m a bit confused myself too.
You appear to have the GND on the same pin than me, but It´s different on Krisztian1997`s schematic

Wait! I think i figured it out. This should be this way:

Please confirm if thats right Krisztian1997!

I got that image from: http://gbatemp.net/goto/post?id=4904401#post-4904401
a user who has already successfully modded his console.
u changed the ground, he has it a different way...

 

[soulrazor]

but that looks just like this and Krisztian1997 said it was wrong
[image deleted]

your diagram is right and his diagram is right too there are 2 ground points for a sd card his point and the one you use

 

[greyneon]

Just connect both Vss together to ground or use any of them. Personally i would connect both to gnd

 

[Moquedami]

I got that image from: http://gbatemp.net/goto/post?id=4904401#post-4904401
a user who has already successfully modded his console.
u changed the ground, he has it a different way...

If it worked fine that way, then this should be the right wiring

 

[Habbert]

Ok so i`m soldering the connector.
I wanna put hot glue on this so the wires don't snap and break off...
is that ok? will the hot glue melt?

Also how much room is there in the 3DS for the connector, is this too big?

 

[greyneon]

No its safe

 

[pelrol]

Thanks a lot bkifft !

I gave a try to your https://github.com/bkifft/RPU instructions and kernel, and I successfully unlocked my bricked 3DS NAND.
Then, putting back my NAND backup with a standard SD adapter was easyas hell !

I owe you an erotic cartoon picture !!!

 

[bkifft]

Thanks a lot bkifft !

I gave a try to your https://github.com/bkifft/RPU instructions and kernel, and I successfully unlocked my bricked 3DS NAND.
Then, putting back my NAND backup with a standard SD adapter was easyas hell !

I owe you an erotic cartoon picture !!!

gratz

nine done (that i know of) X to go

 

[Gizmo1k]

confirmed http://www.usbfirewire.com/Parts/rr-mcb-ext-xxg.html has all five wires just got it and cut into it.

 

[Moquedami]

I`m trying to upload the program to my Arduino following khaalan instructions but I get this error:

This is the directory I created:

I tested my Arduino with the blink demo and it works fine.
Any idea what`s going on?

 

[Abcdfv]

I have an XL, but I haven't seen anyone say actually where DAT3 is on a standard 3DS. Just out of curiosity, is it in some hard to get spot like the CLK?

 

[ryuga93]

I`m trying to upload the program to my Arduino following khaalan instructions but I get this error:

This is the directory I created:

I tested my Arduino with the blink demo and it works fine.
Any idea what`s going on?

That is a bug in the arduino sketch that krisztian forgot to edit,it is just printing problem.the size uses unsigned long long which is not supported by default serial print.You need to edit your print code in arduino folder or just simply comment out the line

 

[Moquedami]

That is a bug in the arduino sketch that krisztian forgot to edit,it is just printing problem.the size uses unsigned long long which is not supported by default serial print.You need to edit your print code in arduino folder or just simply comment out the line

I see Krisztian1997 fixed the error in sd_testy.ino "fixed printing error"

Finally got it working thanks to the help of Khalaan!
Testing on a SD card first

----SD LOCKER MENU----
Programmed by Krisztian and Ryuga
Thanks Coto for your awesome CRC16 algorithm
This program is dedicated to crazyace2011 gbatemp
----------------------
u - UNLOCK
l - LOCK
e - ERASE
x - TERMINATE EXECUTION
----------------------
Starting erase procedure

SET_BLOCKLEN to 1 byte
4

 

[Moquedami]

Mhhhhh........I tried erasing and locking the SD card but it doesn´t seem to have any effect on it.
When I connect it to Windows it shows it normally. No lock of any kind