Toggle sidebar

Hardware Components used on the Switch (mostly the motherboard and main console)

  • Thread starter Thread starter WadsRUs
  • Start date Start date
  • Views Views 276,490
  • Replies Replies 593
  • Likes Likes 23
de9ed said:
while this thread sugge
Click to expand...
I use mcz for the v1 board as well. v2 board has way smaller size than v1. And I found out NFG0QHB372HS2D fit well for the right1/last(sbu1/2) filter and the 4 other TX/RX filter for v2 I pick DLM0NSM900HY2D


And for v2 board hdmi common mode choke filter alternative(Panasonic)
4x left TX/RX can use -- EXC-14CT900U
right1/last 1(sbu1/2) can use -- EXC-X4CT900X
 
Last edited by jkyoho,
  • Like
Reactions: orporp and de9ed
justaplaneguy0 said:
I'm working on a nintendo switch and trying to identify 2 components. I am reflowing and cleaning the BCM4356, and blew these 2 components off the board. 1 of them is an IC of some sort, the other I believe is a cap or an inductor. Could someone please help me identify these components so i can order them either from mouser or digikey?

Thank you in advance!

This is a closeup of the two components i'm trying to identify.
View attachment 239670


This shows the exact location of the board I'm working on zoomed out.
View attachment 239671
Click to expand...
 

Attachments

  • 20210131_102808.jpg
    20210131_102808.jpg
    905.4 KB · Views: 450
Hey gang, happy to see this kinda thread exists. Anyone able to tell me what these two might be? It's right above where the micro SD car clips in.

Got this is a repair from a bad shop, hoping i can get it working again.
 

Attachments

  • 147596947_2917096348574343_3509039102903060170_n.jpg
    147596947_2917096348574343_3509039102903060170_n.jpg
    118.5 KB · Views: 443
Bino said:
Hey gang, happy to see this kinda thread exists. Anyone able to tell me what these two might be? It's right above where the micro SD car clips in.

Got this is a repair from a bad shop, hoping i can get it working again.
Click to expand...
THOSE are two caps
from top to bottom measured:
5uf
250nf
(10k ohm)
try slight larger value since I measure from a crappy donor board, cap value may shift
 
Good afternoon, I have a problem with the left joycon, when it is installed in the switch, it only shows charging, but in the portable mode the console does not see it, it shows that it is connected only via bluetooth. What could be the problem?
 
I'm working on fixing my switch (managed to knock loose a part and can't find it). The port is circled, Without it my fan runs wide open anytime the screen is on. Does anyone know what it is?
LookingComponent.png
 
Hi, I am currently trying to fix my switch after it fell in water. For now the tablet itself works fine, but has no backlignt and some troubles with toutch screen. After checking the board we found one component that is not working at all, if I understood correctly it is in the backlight circut, but I have no idea what it is. If someone can provide me links where I can buy a replacment or just info to feagure what that component is that it would be very nice.
 

Attachments

  • 1.jpg
    1.jpg
    984.3 KB · Views: 390
  • 2.jpg
    2.jpg
    770.8 KB · Views: 421
Last edited by MeoWStraY,
Hi, it's inductor and should have continuity. I dont know exact value but you can possibly have problem with nearby diode too of inductor gone.
 
Last edited by Alfixes,
Here's one for you all! So I bought a lot of broken switches..... most of them are the usual issues (usb port, shorted chip somewhere) but this one..... is kicking my ass lol. When docked it works perfectly zero issues but...… when in handheld mode ZERO on screen, i swapped out the board into a known good one and still zero. any ideas?
 
Hi, I have same issue on one of my fixes. Haven't found solution yet but narrowing down to either components around screen connector area (diode or lcd bga 8316) i dont have time atm but will eventually get to it and will let you know if find solution.
 
  • Like
Reactions: Scottedontknow
Can someone ID this diode please. (i've got a short on it)
It's next to the LCD connector.
The BGA IC in that circuit is a BD8316GWL according to a previous post.
Is it always the same on different hardware revisions of the board ??
My problem is that my switch works in docked mode but not in handheld mode.
Backlight and sound is ok, but no picture.
Obviously on a different board and not the one in the picure.
 

Attachments

  • Diode next to LCD connector.jpg
    Diode next to LCD connector.jpg
    979.9 KB · Views: 442
KCVW said:
Can someone ID this diode please. (i've got a short on it)
It's next to the LCD connector.
The BGA IC in that circuit is a BD8316GWL according to a previous post.
Is it always the same on different hardware revisions of the board ??
My problem is that my switch works in docked mode but not in handheld mode.
Backlight and sound is ok, but no picture.
Obviously on a different board and not the one in the picure.
Click to expand...

Maybe RSX101VA-30 or equivalent
 
please... in Nintendo Switch Lite motherboard...
what is the value of this capacitor in this photos.

on the left side of the FT9CJ chip

switch02.png


switch01.png
 
Can I get help identifying these parts please as I require replacements for my Nintendo switch lite.

ApplicationFrameHost_2021-04-16_20-17-54.jpg 2021-04-25_15-15-12.jpg 2021-04-25_15-12-28.jpg 2021-04-25_15-13-24.jpg

I need replacement parts: (Ignore the 8kohms box that was something I was diagnosing over on TronicFixs with a guy called Severance he pointed me to this forum.

Diode by the inductor coil underneath the BQ and M92 ic's
Replacement inductor coil
FPC connectors for the backlight, LCD, daughter board.
Power connector and various other components that are marked red in the thumbnails, new to the forums so I hope you can see the red boxes.

I just need replacement parts and ideas on where to buy them from thanks

Thanks in advanced for any help.

Kind Regards

Mike
 
Hi everyone, I need some help trying to identify this part circled in the pic for my nintendo. I blew it away during the replacement of the ribbon connector at the back of the board and now I can't find it... Only thing I can read on it is ZBL 628 but no luck so far searching on the internet. So you guys are my last hope. Many thanks in advance!
1.jpg
 
Last edited by golu18,
RedViking said:
I'm working on fixing my switch (managed to knock loose a part and can't find it). The port is circled, Without it my fan runs wide open anytime the screen is on. Does anyone know what it is?View attachment 247350
Click to expand...

also looking for the part. trying to repair a switch with a no spinning fan and that component was soldered opposite way.

LookingComponent.jpg
 
Last edited by note9,

Site & Scene News

Go to forum More news

Popular threads in this forum

Dusk for switch (TLoZ Twilight Princess port)

Homebrew  New Homebrew "Foil Server"?

Homebrew  Full List of N64 Recompilation Switch ports

Hacking  WiFi chip failing and can't boot. is it possible to enable Airplane Mode by editing system save files directly?

Homebrew Tutorial Translation Project  CS2SX — Write Nintendo Switch Homebrew in C#

Is it fixable

Homebrew  Sonic Unleashed Recompiled (Homebrew Port)

Hacking Emulation  Switch Prod Keys downloading from sites okay?