NoI now have it in RCM and have 8 fuses burnt. 6.2.0 is the only firmware i can find that supports 8 fuses but is isn't compatible with ChoiDujour. Is there any firmware that supports both 8 fuses and ChoiDujour?
NoI now have it in RCM and have 8 fuses burnt. 6.2.0 is the only firmware i can find that supports 8 fuses but is isn't compatible with ChoiDujour. Is there any firmware that supports both 8 fuses and ChoiDujour?
This is probably asked a billion times a day, but is there an emunand option available yet outside SXOS? Haven't even looked at my Switch for a while so I'm behind
You could buy a dongle to save time when you're booting CFW, but the only time you need to turn off your Switch is to get the SD card out. And you could even transfer files through USB.So i wanna to use Atmo CFW on my switch, i heard that you cant turn your console to Sleep Mode (by clicking power button once) and after your playtime you have to shut down console. After shutdown you need to use rcm mode to get into CFW.
So my question is ~ Do i really have to do all of these steps just to turn off my console after im done playing or i dont need to bother with that and just let my console go into Sleep Mode? Its sooo messy and takes time to get into CFW everytime after shutdown
How do i use the eMMC SYS to restore unlike a rawnand.bin it is in multiple files.Yes, you can just restore your NAND with only those but if the firmware version is much lower of your boot0/boot1 + eMMC SYS than your current firmware version, then you will need to initialize the system which means you will lose all installed content and save data. You can perform a system initialization in the Maintenance Menu which you enter by holding both volume + and - when turning on the console or using a payload that boots CFW/OFW. Be sure to backup your save data before performing the restore.
Hey guys! I hope you guys can help me out.
I tried to downgrade from 8.0 to 6.4 and now it won't turn on, nor my computer reads it as a device at all. I tried putting in the dock and the dock reads it for a second then turns the light off reading the switch. Does anyone know what's going on?
I should mention something similar happened before but it was "off" for a couple of minutes then it came back. so I waited all night and I still don't have a response from my switch.
Because I couldn’t get my .nsp to install to play games and such and I just wanted something stable and that worksWhy you downgrade down to 6.x when CFW work on 8.0.x?
Because I couldn’t get my .nsp to install to play games and such and I just wanted something stable and that works
Booting lakka can’t ban you. It doesn’t touch the nand.Is there a setup that allows me to boot Lakka (Without CFW/Homebrew) and not get banned on the switch? I've searched this before and all the answers I found were unclear.
I’m sorry I’m new to all of this what does It mean to re-seat the battery? Just take the battery out and put it back in? And what’s can I do if I can bring it back up to 8.0.x what can I do to take the right steps and to get the games to work correctly?Games work fine on 8.0.x if you used the correct sig patches and nsp that is properly converted, press the power button for 30 seconds see if there is any reaction to see if it would power on, second thing you can do is try to re-seat the battery.
I’m sorry I’m new to all of this what does It mean to re-seat the battery? Just take the battery out and put it back in? And what’s can I do if I can bring it back up to 8.0.x what can I do to take the right steps and to get the games to work correctly?
Alright I’ll try that thank you for yourYea it mean open it up, unplug the battery and plug in back in, and see if power on, if you can't get it to power on there is nothing much you can do.
I updated from 6.2.0 to 7.0.1 and everything works fine.Sxos users, have anyone updated their emuNAND from 6.2 to 7.x or 8.0? Did you previously nsp installed games keep working?