I'm glad your name is safe, but his switch is fubar.I just backup my name yesterday using 4.1 with no problems
Nope. and now it wont boot back into hekate 3.2 im gonna run meloader again then try hekate as that worked before.can you boot into maintenance mode?
Best thing to do, would be build NAND from scratch. Upload PRODINFO somewhere and email me biskeys and I`ll take a look if you like. In PM though because not sure about rules.Nope. and now it wont boot back into hekate 3.2 im gonna run meloader again then try hekate as that worked before.
Keys are console specific budd arent they.. dont want you fcking up your switch.,,Best thing to do, would be build NAND from scratch. Upload PRODINFO somewhere and email me biskeys and I`ll take a look if you like. In PM though because not sure about rules.
Yes I know that.Keys are console specific budd arent they.. dont want you fcking up your switch.,,
i know thanks it does not workhold down power button for 20 seconds to make sure it's off. Then Hold + and - volume buttons and press power.
I audited the code and I can safely say it does not, hard to do that with some alternatives. :v)So the question is
Does Hekate have brickcode
hey your switch is dead go buy another
I had an experience where I too was blaming hekate for my switch's dysfunction but it ended up being faulty hardware as confirmed by me sending it to nintendo and them repairing it. If your switch is less than a year old it's still covered. You don't even need a receipt as they know exactly when you bought it from the serial number. And I can assure you Nintendo can't tell you've ran hekate.its not a new switch but it was a untouched switch... the only time it run hekate was today.. trying to backup 5.1.0 rawnand.bin with hekate 4.1 got to 99% dumping froze... could not cancel dump with key combo or go back. had to hard reset the switch.. at reboot it failed to load into stock or hekate payload.... rebuild the nand did nothing. had to use hacdiskmount to do that... battery is fine and fully charged... Switch was absolutely fine until i used hekate today. Sd card is fine also not that it affects the boot anyway...
Annoyed is a understatement..
I am done with this, and am sending it off to matty, hes gonna run some tests and check the board for me..
as i have exhausted my self today trying to find the fault... but it all happend aster using hekate dump,, yes yes i know it shouldnt happen if im only dumping nand. but well absolutley fine till dumping, gets to 99% then dies ? i dunno what it is or what to blame maybe a coincidence but fuck my life.. thank you all for supporting me on this,
the nand guy gets nand fcked haha ... Il let you know the outcome when i can..
wait a minute. How are you trying to boot stock?its not a new switch but it was a untouched switch... the only time it run hekate was today.. trying to backup 5.1.0 rawnand.bin with hekate 4.1 got to 99% dumping froze... could not cancel dump with key combo or go back. had to hard reset the switch.. at reboot it failed to load into stock or hekate payload.... rebuild the nand did nothing. had to use hacdiskmount to do that... battery is fine and fully charged... Switch was absolutely fine until i used hekate today. Sd card is fine also not that it affects the boot anyway...
Annoyed is a understatement..
I am done with this, and am sending it off to matty, hes gonna run some tests and check the board for me..
as i have exhausted my self today trying to find the fault... but it all happend aster using hekate dump,, yes yes i know it shouldnt happen if im only dumping nand. but well absolutley fine till dumping, gets to 99% then dies ? i dunno what it is or what to blame maybe a coincidence but fuck my life.. thank you all for supporting me on this,
the nand guy gets nand fcked haha ... Il let you know the outcome when i can..
Hekate 4.1, not Horizonwait a minute. How are you trying to boot stock?
Because 5.0 burns a efuse. which mean 4.1 can't boot without hekate. And I would check your microsd, it sounds like a faulty one.