Hacking [Help]9.1J New 3ds to A9HL

[Svyline]

How should I proceed? upgrade to 9.2 or do part 1 on Plailect guide?

 

[CrispyYoshi]

How should I proceed? upgrade to 9.2 or do part 1 on Plailect guide?

Attempt to do Part 1. If you run into any issues then yes, you will want to update to 9.2: https://github.com/Plailect/Guide/wiki/9.2.0-Update

 

[Akira]

How should I proceed? upgrade to 9.2 or do part 1 on Plailect guide?

Hi, You can proceed on doing Plailect's guide without issue. I also had a 9.1J sysnand and everything went smooth.

 

[Ugothacked]

I did it with my 2 N3DS Jp, they were both on 9.1 and worked perfectly

 

[Just3DS]

9.1 on JPN is same as 9.2 on the guide.
So yeah, just replace 9.2 with 9.1 in the guide and you're good to go.

Though, (it goes without saying) wherever they ask you to use appropriate firmware files for downgrade/upgrade for your console region do follow that.

 

[dimmidice]

i had 9.0 EUR firmware and it worked just fine. according to the guide 9.0 and 9.1 are functionally the same as 9.2

https://github.com/Plailect/Guide/wiki/Get-Started

f you are on 9.0.0 or 9.1.0 you are fine where you are as both are almost identical to 9.2.0.

 

[Cuphat]

Yeah, the range of FWs required is 9.0 - 9.2. 9.1 will work fine.

 

[Svyline]

okie I ran into a roadblock, after part 1 section 8 it doesnt get pass the green, yellow and red screen. should I just keep trying? did it 10+ times and still same result.

--------------------- MERGED ---------------------------

I am connected to wifi and have the starter folder into root of sd.

 

[retrofan_k]

make sure you scanned your correct 9.1.xx jp qr code and not 9.2 even though they are the same technically if you are using browser hax as the entry point and make sure the boot file is on the root too.

 

[EmperorOfCanada]

okie I ran into a roadblock, after part 1 section 8 it doesnt get pass the green, yellow and red screen. should I just keep trying? did it 10+ times and still same result.

--------------------- MERGED ---------------------------

I am connected to wifi and have the starter folder into root of sd.

Try manually typing in the address? I never had any issues when manually typing in the address.

 

[Svyline]

im using the qr code provided on part 1 section 8, boot file is on root.

--------------------- MERGED ---------------------------

Try manually typing in the address? I never had any issues when manually typing in the address.

did this also but to no avail.

 

[retrofan_k]

is the browser actually working on other sites?

 

[HiddenRambler]

I ran into the same issue and i believe it was cause by the sd card not being inserted well. removing and reinserting the card properly fixed it.

 

[Svyline]

I ran into the same issue and i believe it was cause by the sd card not being inserted well. removing and reinserting the card properly fixed it.

ill try that, im @ work right now. I'll update you guys in 8 hours lol. you guys are the best

 

[Svyline]

Hi guys, I'm at part 3 Between section 18 and 19. I keep getting a black screen and it wont boot to rednand. should I just keep trying until it boots to rednand?

 

[EmperorOfCanada]

Hi guys, I'm at part 3 Between section 18 and 19. I keep getting a black screen and it wont boot to rednand. should I just keep trying until it boots to rednand?

You are launching LUMA, yes?

 

[Svyline]

yes @ HBL, just keep getting black screen all the time.

 

[EmperorOfCanada]

yes @ HBL, just keep getting black screen all the time.

How are you launching HBL?

 

[Svyline]

Hold L while booting

 

[EmperorOfCanada]

Hold L while booting

Try this if you havent
https://github.com/Plailect/Guide/wiki/Troubleshooting#black-screen-on-rednand-boot