Hey fellas. I attempted to install a PicoFly clone off AliExpress today. It went well, expect like an idiot I let a tiny resistor fly off the board while tidying up. I now get a purple screen on boot.
From my googling it appears it's a 4.7k ohm 5% resistor. Is that right?
Unfortunately no photos right now, but I believe it was a vertical resistor connected to the pad labeled "A" on the V5 mod chip set. I hope that makes sense, I apologize I'm a bit new to this
Do you upgrade your console with picoflytoolbox? I upgrade it from 2.73 to 2.75.
It was succesfull (this was wrote after the upgrade) after that i restarte the cosole. Than i start ofw and get a error message. Partition table is empty
Without chip i get a purble screen. i check the firmware and it was still on 2.73 .... so the upgrade was not succesfull.
this is not my first upgrad with picofly toolbox but my first with 2.75....
i upgrade it with my pc and works. Now my picofly is on 2.75 but the eemc is empty and purble screen.
Unfortunately no photos right now, but I believe it was a vertical resistor connected to the pad labeled "A" on the V5 mod chip set. I hope that makes sense, I apologize I'm a bit new to this
let's not talk nonsense, the eristas all want double resistance on dat and cmd, and it's not an installation problem. I also thought it was impossible on OLEDs but some models require double resistance.
The symptoms of an empty partition table is the same if you fried the CMD resistor.
The system files are probably there but the console will fail to load them its not just hekate failing to identify them. I haven't tested pulling the chip to see if the files are still intact before restore but if this ever happens again I'll make sure to verify it on my system.
The dead give away here is to not update these clones using the toolbox.
One more thing, if you already updated to 2.75 using the toolbox (by pressing the update a couple of times) and use the retrain function on the clones, it will also makes the eMMC go away.
One more thing, if you already updated to 2.75 using the toolbox (by pressing the update a couple of times) and use the retrain function on the clones, it will also makes the eMMC go away.
Data Train reset or something like that? I used it after updating to 2.75 (and after 40 minutes of restoring backup) and when I restarted the console, I got a purple screen and an empty eMMC partition table (again).
i dont have a backup .. damn .. that it i can used it for paperweight. And maybe the only solution was a 200ohms on Dat0 .. maybe ..
Why did this happen? from upgrade to 2.73 was no problem anymore from 2.73 to 2.75 it deleteds your eemc?
It's still possible to retrieve data from the eMMC. Like any type of non-volatile memory, your data would still be retained unless you rewrite. So whatever data is stored on the chip should still be there even if you delete. Get one of those cheap programmers that can read the switch eMMC and try to recover the partitions, you only need one part.
Data Train reset or something like that? I used it after updating to 2.75 (and after 40 minutes of restoring backup) and when I restarted the console, I got a purple screen and an empty eMMC partition table (again).
i've read fast the code on the mechanism of update via picoflytoolbox, and data train. It seems possible something goes wrong.
To understand more clearly, need to read the code in depth, but i just doesn't have lot of time.
I will stay away from the picofly toolbox for now, until i am sure with the algorithm.
Do you upgrade your console with picoflytoolbox? I upgrade it from 2.73 to 2.75.
It was succesfull (this was wrote after the upgrade) after that i restarte the cosole. Than i start ofw and get a error message. Partition table is empty
Without chip i get a purble screen. i check the firmware and it was still on 2.73 .... so the upgrade was not succesfull.
this is not my first upgrad with picofly toolbox but my first with 2.75....
i upgrade it with my pc and works. Now my picofly is on 2.75 but the eemc is empty and purble screen.
Yes, the switch on the vid is updated by toolbox from 2.73 to 2.75.
I had a vid for that, initially after update I select ofw and update failed but then I select "reboot to normal" and 2.75 update success.
i installed picofly on a switch oled and after that right joy-con is charging but not detected in handheld mode, wireless is working. The problem is not in joy-con or rail. I think that the problem is on motherboard . Does anyone know what component on motherboard is causing this
As each year passes, retro games become harder and harder to play, as the physical media begins to fall apart and becomes more difficult and expensive to obtain. The...
After several months of work, the Harbour Masters 64 team have released their first public build of 2Ship2Harkinian, a feature-rich Majora's Mask PC port. This comes...
Retro handheld manufacturer Anbernic has revealed its first clamshell device: the Anbernic RG35XXSP. As the suffix indicates, this handheld's design is inspired by...
With the vast success of Super Mario Maker and its Switch sequel Super Mario Maker 2, Nintendo fans have long been calling for "Maker" titles for other iconic genres...
After rumour got out about an upcoming NES Edition release for the famed Nintendo World Championships, Nintendo has officially unveiled the new game, titled "Nintendo...
Ubisoft has today officially revealed the next installment in the Assassin's Creed franchise: Assassin's Creed Shadows. This entry is set in late Sengoku-era Japan...
Another day, another great emulator that makes its way into the Apple Store for more users to enjoy. With Apple opening its store up to videogame emulators earlier...
After a little more than three years of exclusivity with the Epic Games Store, Square Enix has decided to bring their beloved Kingdom Hearts franchise to Steam. The...
Palmer Luckey is known for his pursuits into the world of virtual reality, having founded Oculus and designed the Rift VR headset. Prior to the $2 billion dollar...
Drumming up hype by teasing a new product, with its formal reveal to come next month is Asus, who just announced the latest revision to their ROG Ally handheld...
Palmer Luckey is known for his pursuits into the world of virtual reality, having founded Oculus and designed the Rift VR headset. Prior to the $2 billion dollar...
As each year passes, retro games become harder and harder to play, as the physical media begins to fall apart and becomes more difficult and expensive to obtain. The...
After several months of work, the Harbour Masters 64 team have released their first public build of 2Ship2Harkinian, a feature-rich Majora's Mask PC port. This comes...
Ubisoft has today officially revealed the next installment in the Assassin's Creed franchise: Assassin's Creed Shadows. This entry is set in late Sengoku-era Japan...
After a little more than three years of exclusivity with the Epic Games Store, Square Enix has decided to bring their beloved Kingdom Hearts franchise to Steam. The...
After rumour got out about an upcoming NES Edition release for the famed Nintendo World Championships, Nintendo has officially unveiled the new game, titled "Nintendo...
Another day, another Nintendo DMCA takedown against fan-made content.
Just a few minutes ago, Nintendo issued a DMCA takedown notice against a widely known and...
Sony is once more attempting to reintroduce players to their older library of games by re-releasing classic PlayStation 2 titles onto the PlayStation Store. During...
Retro handheld manufacturer Anbernic has revealed its first clamshell device: the Anbernic RG35XXSP. As the suffix indicates, this handheld's design is inspired by...
With the vast success of Super Mario Maker and its Switch sequel Super Mario Maker 2, Nintendo fans have long been calling for "Maker" titles for other iconic genres...
yo guys the sonic x shadow generations trailer dropped today, and shadow just straight up decided, and i hate (love) to bring this dead meme up, but, it's morbin time