Hacking SWITCH NOOB PARADISE - Ask questions here

[guily6669]

Is there no mem temp sensor on Switch? I can't find much info about it...

I suspect my memories might be running hot due to very thick thermal pads at 1862mhz (Erista V1).

Also I didn't do this "Add kip1=atmosphere/kips/loader.kip to boot entry" cause on the 2 latest versions of OC Suite it seems to work out-of-the-box for Erista and don't seem to need that line to load anymore. Does anyone know if adding that line makes any difference?

 

[DuckNoir]

Hi, sx os is dead and cant load new backup games right ?

 

[binkinator]

Hi, sx os is dead and cant load new backup games right ?

Correct. SXOS can’t run games that require anything above 11.0.0. Anything at 11.0.0 and below is fine though.

 

[BruhGimmeName]

I never thought it might be the sd card the problem, tomorrow i'ill try to test on another sd

I can confirm that all my issues stemmed from the SD card.
After running H2testw I could see that it was indeed fake, having a real size of 55gb rather than 512gb. This no doubt messed with the way hekate partitioned it, and resulted in a corrupted RAW partition on which emuMMC could not be properly written.

After obtaining a good SD card I was able to create and boot into emuMMC without issues.

I hope this helps you, too.

 

[anthony001]

if i have sd card containing a official firmware 13.x.x and a sd card with 14.x.x. or 15.x.x. will i be able to use one and the other like one day i will use my 13.x.x. and the next day i will use 14.xx.x then next day i will do 13.x.x. again

do i need to power off completely or can i do it in hekate menu?

 

[Draxzelex]

if i have sd card containing a official firmware 13.x.x and a sd card with 14.x.x. or 15.x.x. will i be able to use one and the other like one day i will use my 13.x.x. and the next day i will use 14.xx.x then next day i will do 13.x.x. again

do i need to power off completely or can i do it in hekate menu?

What do you mean by "sd card containing"? Having the firmware files of those versions on the SD card won't magically boot those firmware versions. Do you mean emuMMC? If you have emuMMC on different SD cards that are running the firmware versions you listed, you can boot into them at any time. And assuming you are talking about emuMMC, you can switch emuMMC via the Hekate menu.

 

[Blakejansen]

AutoRCM at its core is a corruption of BOOT0. BOOT0 is only used, as the name implies, to boot up the console. Even if you were somehow able to completely destroy BOOT0 without a backup, the worst that would happen is that you will permanently have AutoRCM. Although it is worth mentioning that its possible to recreate BOOT0 from scratch with certain tools.

A brick means the device has the electronical functionality of a brick. Even if you were somehow make it unable to boot Horizon which is the name of the Switch operating system, you could technically still use RCM to boot other OS's like Lakka, Android, and Linux.

If you want to read up on further on all of the ins and outs of AutoRCM, you can read this thread that completely covers the mod from top to bottom.

Why a permanent autorcm though? If BOOT0 got corrupted without a backup, I could just wait until Nintendo release a new system update and then run hekate to sysfw right? Still haven't decided on autorcm, will read the thread you linked.

 

[fparseb]

This error is typically a result of an outdated Hekate.

You can update Hekate here:
https://github.com/CTCaer/hekate

More information about keeping your Switch up to date can be found here:

https://rentry.org/SwitchHackingIsEasy

Seems we have some improvement. Thanks for that, @binkinator .

After update Hekate to the last version, now in HW & Fuses info I have:
Burnt Fuses (ODM 7/6): 17 - 0 (HOS: 15.0.0+)

The problem is if I try to boot into stock, I have directly a screen blue. Nothing else, no text no error.

[Stock]​

fss0=atmosphere/package3​

stock=1​

emummc_force_disable=1​

icon=bootloader/res/icon_switch.bmp​

Maybe I must update Atmosphere now even I'm not using it?

I'm sorry for making so much questions. I want to be careful with these actions trying to avoid irreparable steps. Thanks so much for your patience.

 

[binkinator]

Seems we have some improvement. Thanks for that, @binkinator .

After update Hekate to the last version, now in HW & Fuses info I have:
Burnt Fuses (ODM 7/6): 17 - 0 (HOS: 15.0.0+)

The problem is if I try to boot into stock, I have directly a screen blue. Nothing else, no text no error.

[Stock]​

fss0=atmosphere/package3​

stock=1​

emummc_force_disable=1​

icon=bootloader/res/icon_switch.bmp​

Maybe I must update Atmosphere now even I'm not using it?

I'm sorry for making so much questions. I want to be careful with these actions trying to avoid irreparable steps. Thanks so much for your patience.

Yes, update your atmosphere to the latest here:

https://github.com/Atmosphere-NX/Atmosphere/releases

Atmosphere only exists on your SDCard and will not harm anything.
(You simply remove the SDCard to remove both Hekate and Atmosphere BTW)

Post automatically merged: Jan 13, 2023

Hi, I'm trying to install tinfoil through dbi but the error " NCA Signatures Invalid " appears and I found about the konami master code but I don't know where to use it.

Install tinfoil by downloading the nro installer file (conveniently named tinfoil.nro) and placing it in your /switch directory. Then open hbmenu using title override and run it to install tinfoil.

 

[Draxzelex]

Why a permanent autorcm though? If BOOT0 got corrupted without a backup, I could just wait until Nintendo release a new system update and then run hekate to sysfw right? Still haven't decided on autorcm, will read the thread you linked.

I guess you could do that as well but sometimes you might already be on the latest firmware and sometimes it takes months for Nintendo to release a new firmware. As an example, the current and latest firmware 15.0.1 was released on Halloween, October 31st which was almost 3 months ago.

 

[walackson]

Yes, update your atmosphere to the latest here:



Atmosphere only exists on your SDCard and will not harm anything.
(You simply remove the SDCard to remove both Hekate and Atmosphere BTW)

Post automatically merged: Jan 13, 2023

Install tinfoil by downloading the nro installer file (conveniently named tinfoil.nro) and placing it in your /switch directory. Then open hbmenu using title override and run it to install tinfoil.

I tried that but there is an error when using the auto installer and it does not run directly from the applet.

 

[binkinator]

I tried that but there is an error when using the auto installer and it does not run directly from the applet.

Correct. You must use title override. Tinfoil needs all memory available in order to install.

To use title override you must have at least one game installed. I typically use Tinwoo to install Othello nsp (only 112M game). Once you have a title on your main screen you can then open hbmenu with full memory available by pressing and holding the (R)ight shoulder button down and clicking on a game title. Keep holding (R) until hbmenu appears. Only then will you be able to launch the tinfoil_installer.nro file.

 

[ghostgenji]

Guys, does anyone know how to change the resolution on the nintendo switch display?I want to increase autonomy by lowering the resolution to 480p

 

[Hayato213]

Guys, does anyone know how to change the resolution on the nintendo switch display?I want to increase autonomy by lowering the resolution to 480p

If you wanted to change the TV resolution for the dock, go to system settings -> tv settings -> tv resolution.

 

[fparseb]

Yes, update your atmosphere to the latest here:

https://github.com/Atmosphere-NX/Atmosphere/releases

Atmosphere only exists on your SDCard and will not harm anything.
(You simply remove the SDCard to remove both Hekate and Atmosphere BTW)

Post automatically merged: Jan 13, 2023

Install tinfoil by downloading the nro installer file (conveniently named tinfoil.nro) and placing it in your /switch directory. Then open hbmenu using title override and run it to install tinfoil.

I've updated Atmosphere and now it's working as before with the new FW version. Thanks so much, @binkinator

The only issue I have now is the same I have before that and I've detailed in other post.

https://gbatemp.net/threads/switch-lite-not-booting-ok-to-ofw.600534/#post-9615326​

Basically, when boot to Stock I have Boot loop after Nintendo Switch logo. After some minutes (it's random, around 5-10 minutes), it finally boots to OS.

If I try to do the hard reset pressing both volume buttons it goes directly and the reinstallation works OK until the next reboot.

I've resoldered the entire chip again and same issue.

But in any case, it's not important.

Thank you so much for your time and help on this matter.

 

[BruhGimmeName]

Is it 'safe' (as in, from flagging your account for future bans) to play in CFW sysMMC all the time, if you never do anything you wouldn't be doing on stock? I mostly wanna know so I can avoid manually re-injecting the RCM payload when I wanna use my emuMMC.

 

[Hayato213]

Is it 'safe' (as in, from flagging your account for future bans) to play in CFW sysMMC all the time, if you never do anything you wouldn't be doing on stock? I mostly wanna know so I can avoid manually re-injecting the RCM payload when I wanna use my emuMMC.

If you installed NSP on Sysnand you would eventually get banned, if you ran homebrew it is moderate chance, can't guarantees no ban.

 

[BruhGimmeName]

If you installed NSP on Sysnand you would eventually get banned, if you ran homebrew it is moderate chance, can't guarantees no ban.

I just want to confirm that by not doing either (installing NSPs or running homebrews) and simply being in CFW while in sysnand that shouldn't result in a ban, even if using internet services.

 

[Hayato213]

I just want to confirm that by not doing either (installing NSPs or running homebrews) and simply being in CFW while in sysnand that shouldn't result in a ban, even if using internet services.

You would be fine.

 

[guily6669]

Does anyone know where does tinfoil have the hekate payload and if it can be updated? (hope it's not hard coded into the app)

It keep screwing my hekate, I updated to 6.01 but after a few days I sent the payload which I even updated on my phone and said I had old NYX, I realized Tinfoil keep installing Hekate 5.9 if I use it's payload feature to go into hekate despite having latest 6.01 payload on my mSD and on my phone