Help. I HAD a 6.1 sysNAND and 6.1 emuNAND. Never used sysNAND. Only made backup of 4.1 sysNAND before hacks
the Switch boots up into RCM mode. Then I click emunand or custom firmware. Then the Nintendo screen flashes. Then Black screen. Then Nintendo Switch screen. IT then freezes on this screen and never moves on. I noticed this after I installed a fire emblem game update and DLC from a site I was pretty familiar with. Once I backed out to home screen it froze. Then my switch could never turn on properly.
I turn off my switch my holding the power for 15 seconds. Charge the SX pro. Then try again and always get the same results.
Auto RCM was on. I turned it off just in case.
Booting into Original firmware doesnt work anymore EITHER!!!! I never used original firmware
Even though AutoRCM is off, If I turn on the console without dongle, RCM jig and SD card it wont boot up. screen doesnt even light up.
I used Hekate to restore my eMMC BOOT0/1 and eMMC RAW GPP (Exfat only) from my original backup. It still doesnt work. RCM is uninstalled. Booting the system with no SD card, No SXPro dongle, and No Jig results in No boot.
Booting into CFW from SXpro still has same Nintendo Switch logo hang. HELP
I thought it was a fuse issue since I have burned 7 fuses (6.1) but restored to 4.1
However I followed the guide (https://gbatemp.net/threads/how-to-...nofficially-without-burning-any-fuses.507461/)
And patched it to 4.1 including BOOT0/1 that didn’t work. Then tried patching to 5.1 and 6.1 that didn’t w ork and I didn’t even see the switch logo when I did those.
Im lost for what to do really. Booting into Hekate then loading Original FW doesn’t work. Loading CFW from SX OS and Atmosphere payload still hangs.
Also I noticed when I dump my keys BISKey2 and 3 are both the same. Not sure if that matters.
Hekate also shows TSEC Key 3 as 0000000000000000000000000000000
What do I do?
the Switch boots up into RCM mode. Then I click emunand or custom firmware. Then the Nintendo screen flashes. Then Black screen. Then Nintendo Switch screen. IT then freezes on this screen and never moves on. I noticed this after I installed a fire emblem game update and DLC from a site I was pretty familiar with. Once I backed out to home screen it froze. Then my switch could never turn on properly.
I turn off my switch my holding the power for 15 seconds. Charge the SX pro. Then try again and always get the same results.
Auto RCM was on. I turned it off just in case.
Booting into Original firmware doesnt work anymore EITHER!!!! I never used original firmware
Even though AutoRCM is off, If I turn on the console without dongle, RCM jig and SD card it wont boot up. screen doesnt even light up.
I used Hekate to restore my eMMC BOOT0/1 and eMMC RAW GPP (Exfat only) from my original backup. It still doesnt work. RCM is uninstalled. Booting the system with no SD card, No SXPro dongle, and No Jig results in No boot.
Booting into CFW from SXpro still has same Nintendo Switch logo hang. HELP
I thought it was a fuse issue since I have burned 7 fuses (6.1) but restored to 4.1
However I followed the guide (https://gbatemp.net/threads/how-to-...nofficially-without-burning-any-fuses.507461/)
And patched it to 4.1 including BOOT0/1 that didn’t work. Then tried patching to 5.1 and 6.1 that didn’t w ork and I didn’t even see the switch logo when I did those.
Im lost for what to do really. Booting into Hekate then loading Original FW doesn’t work. Loading CFW from SX OS and Atmosphere payload still hangs.
Also I noticed when I dump my keys BISKey2 and 3 are both the same. Not sure if that matters.
Hekate also shows TSEC Key 3 as 0000000000000000000000000000000
What do I do?
Last edited by Emeraldman94,
