NTRBoot Released!

It's here!
ntrboot_checklist_2.png

Info

@Normmatt has created a way to run B9S .firm files from bootrom via a DSi Flashcard and a magnet! This works on every 3DS on any firmware version.

For installation without a PC, user @TheCyberQuake has created a pack which will automatically install B9S and copy over essential starter homebrew from the flashcard's SD to the 3DS's. This will mainly be used for PC-less B9S installations. If you have a PC with you, use 3ds.guide. Read more here: https://gbatemp.net/threads/481141/

How does this work?

This works because of a flaw in the bootrom. Before the bootrom boots the NAND, it checks to see if Start+Select+X is held down, and if the shell is closed. If these requirements are met, it will boot an NDS cartridge from the bootrom. This give that cartridge bootrom access. You might be wondering how you'd hold down buttons while the shell is closed, and why you need a magnet. If you put a magnet in a specific spot on the 3DS, it will go into sleep mode. Using this, you can boot the NDS cartridge with the buttons held down while in sleep mode! Using a reflashable flashcard, you can boot B9SInstaller using the flashcard, and easily install it on your 3DS.
The 2DS doesn't need a magnet since a switch puts it to sleep instead of a magnet.

What does this mean?

  1. Any 3DS model on any firmware can be hacked with minimal effort
  2. You can unbrick any 3DS model from any type of brick.
    - Remember, you don't need a NAND backup for this. Just do a CTRTransfer.
    - This does not apply to MCU bricks.
  3. Even consoles with fried NAND, or even the NAND chip physically removed, can use this
This is incredibly impressive stuff, and will most likely be released soon! edit: now!

FAQ

Q: Can Nintendo patch this?
A: Nope! Not without a new hardware revision.

Q: My flashcard is blocked by my firmware! Can I still use this?
A: Yes! The flashcard blacklist is not enabled on the bootrom.

Q: Why can't this work with my flashcard?
A: The installation requires you to flash NTRBoot to the flashcard's nand. Most DS flashcards, such as the original R4, have a ROM, which is not flashable.

Q: Can I install NTRBoot on my flashcard without another 3DS system?
A: If you can run NDS roms on your 3DS with it, then yes. If it's blocked on your 3DS version, then you'll need another 3DS system to use it.

Q: Will my 3DS flashcard work?
A: No, only the NDSi flashcards listed above.

Q: Will any other flash cards work?
A: Only the ones listed in the OP. However keep in mind that flashcards such as the DSTT, Supercard DS2 and R4 SDHC Dualcore are planned to be supported in the future.

Q: I tried to do this with my cartridge and it didn't work?
A: It doesn't work with regular DS cards.

Q: Can I unbrick from a ____ brick?
A: Considering the card has access to the bootrom, yes! This can unbrick any brick (except MCU), unless you've taken a knife to the motherboard.

Q: Can I install B9S on the latest firmware with this?
A: Again, since the card has access to the bootrom, you can do this easily! Just plug in your flashcard, boot up using the magnet and button combination, and install.

Q: Does this work on the New Nintendo 2DS XL?
A: Yes!

:arrow: Release
:arrow: Guide
:arrow: Free NTRBoot Flashing
:arrow: Free B9S Installations

Here is SciresM's post about this

Please see SciresM's presentation on bootromhax.
 
Last edited by Deleted member 381889,

MrJason005

√2
Member
Joined
Nov 26, 2014
Messages
2,521
Trophies
0
Location
Κάπου
XP
1,609
Country
Greece

nastys

ナースティス
Member
Joined
Aug 5, 2014
Messages
1,730
Trophies
0
Age
26
Location
Earth
XP
1,794
Country
Italy
For those who don't have a magnet: I did it with a toothpick.
I used it to hold X while I used my other hand to press SELECT, START and POWER with the lid almost closed and it worked!
 
  • Like
Reactions: Quantumcat

nastys

ナースティス
Member
Joined
Aug 5, 2014
Messages
1,730
Trophies
0
Age
26
Location
Earth
XP
1,794
Country
Italy
I'm guessing it was really clumsy
I was wrong, I thought it had worked because it loaded the Luma setup screen. However it should be possible if you have very thin fingers or if you put something between the screen and the buttons.
I'll just find a compatible magnet, other than my tablet :rofl:
 

Majickhat55

The Red Woman
Member
Joined
Mar 28, 2016
Messages
4,936
Trophies
1
Age
36
Location
Asshai
XP
2,958
Country
United States
I was wrong, I thought it had worked because it loaded the Luma setup screen. However it should be possible if you have very thin fingers or if you put something between the screen and the buttons.
I'll just find a compatible magnet, other than my tablet :rofl:
Technically that still wouldn't be "without" a magnet, since there is one built in to the console that triggers sleep on hinged devices Lol.
 

Bateees

Well-Known Member
Newcomer
Joined
May 4, 2015
Messages
92
Trophies
0
XP
136
Country
United States
I have been trying to get this to work for the past hour. I still have my armloaderhax on my source 3DS XL and not bootstrap. When I copy all of the files as I am supposed to I still boot into GodMode9 and not ntrbootflasher. Is there a way I can use GodMode9 instead or am I doing something wrong? Also inside the flashcard am I supposed to have the Acekard files on the micro SD card or is it supposed to be formatted?
 

MrJason005

√2
Member
Joined
Nov 26, 2014
Messages
2,521
Trophies
0
Location
Κάπου
XP
1,609
Country
Greece
I have been trying to get this to work for the past hour. I still have my armloaderhax on my source 3DS XL and not bootstrap. When I copy all of the files as I am supposed to I still boot into GodMode9 and not ntrbootflasher. Is there a way I can use GodMode9 instead or am I doing something wrong? Also inside the flashcard am I supposed to have the Acekard files on the micro SD card or is it supposed to be formatted?
The flashcart doesn't need an SD card in it.
Are you using a second 3DS?
 

Site & Scene News

Popular threads in this forum

General chit-chat
Help Users
    I @ idonthave: :)