No Video after writing Xell

[gonefishing1975]

Hey

I installed the RGH3 mod on a 360 Trinity motherboard (I have done several before) The issue I have is after writing Xell I don't get any videoin order to get the CPU key. I decided to write the original NAND back but now the LED is green for several seconds and it truns red and still no video. I have never had this issue before. I used a 5k resistor like usual triple checked the soldering and looks perfect. I would like to even just get it to boot with factory NAND but no go. Any ideas?

***Note*** I did notice in JRunner that the Kernel Version in XeBuild is set to 17559 but in the consol info section I see CF & CG are 17349 not sure if this is correct or if it even matters

Thanks

 

[gonefishing1975]

So i removed my 5k resistor and installed a 3k. If i turnon the console using the eject button I now get Xell and can grab the CPU key. I then created my image and wrote that to the nand but if i use the power button NOT the eject button no video and the power LED flashes non stop. Any ideas?

 

[XRed_CubeX]

So i removed my 5k resistor and installed a 3k. If i turnon the console using the eject button I now get Xell and can grab the CPU key. I then created my image and wrote that to the nand but if i use the power button NOT the eject button no video and the power LED flashes non stop. Any ideas?

red or green led?

 

[gonefishing1975]

I now have video but only with RCA Jacks nothing from the HDMI port unless I use the elect button to boot into Xell then HDMI works

 

[XRed_CubeX]

I now have video but only with RCA Jacks nothing from the HDMI port unless I use the elect button to boot into Xell then HDMI

With the RCA cable connected go into the display settings from the dashboard, enable HDMI output, unplug the RCA and try with HDMI

 

[gonefishing1975]

With the RCA cable connected go into the display settings from the dashboard, enable HDMI output, unplug the RCA and try with HDMI

This console for some reason locks up when I try todo certain things, If I try to connecto to WiFi is locks up, can't enble HDMI, cannot rest to factory defaults etc. Not sure what's up with this console

 

[gonefishing1975]

So no matter what I do the console won't do the following, when I press "A" to try the isses below you hear that the button was pressed and the sdcreen flashes but nothing happens or for some the console locks up for a few seconds then reboots. Any ideas?

-Connect to the internet
-format the hard drive
-delete old profile
-update

 

[Vstromakias]

create a new updflash.bin with jrunner and check patches/nohdmiwait and usbdsec. write it to the console and try again

 

[gonefishing1975]

create a new updflash.bin with jrunner and check patches/nohdmiwait and usbdsec. write it to the console and try again

What Do you mean create a new updflash.bin? Like a donor nand?

 

[Vstromakias]

create a new updflash.bin with jrunner and check patches/nohdmiwait and usbdsec. write it to the console and try again

What Do you mean create a new updflash.bin? Like a donor nand?

with jrunner you kept 2 (or 1) nand backup. with this and the cpu key you created the final file which was an updflash.bin file. with the files you have kept, create a new one but also select the options I wrote for you. pass the new file to the console and try.

 

[gonefishing1975]

create a new updflash.bin with jrunner and check patches/nohdmiwait and usbdsec. write it to the console and try again


with jrunner you kept 2 (or 1) nand backup. with this and the cpu key you created the final file which was an updflash.bin file. with the files you have kept, create a new one but also select the options I wrote for you. pass the new file to the console and try.

Perfetc thanks I will try that out

Post automatically merged: Jul 6, 2025

create a new updflash.bin with jrunner and check patches/nohdmiwait and usbdsec. write it to the console and try again


with jrunner you kept 2 (or 1) nand backup. with this and the cpu key you created the final file which was an updflash.bin file. with the files you have kept, create a new one but also select the options I wrote for you. pass the new file to the console and try.

Thanks it's all working now. You Rock!!

 

[Vstromakias]

Perfetc thanks I will try that out

Post automatically merged: Jul 6, 2025

Thanks it's all working now. You Rock!!

If you also choose usbdsec, you will be able to use other controllers besides the 360. Easy and cheap.

https://github.com/wiredopposite/OGX-Mini

https://github.com/wiredopposite/OGX-Mini/releases/tag/v1.0.0-alpha3

 

[XRed_CubeX]

If you also choose usbdsec, you will be able to use other controllers besides the 360. Easy and cheap.

https://github.com/wiredopposite/OGX-Mini

https://github.com/wiredopposite/OGX-Mini/releases/tag/v1.0.0-alpha3

Oh so you don't even need the Magic NS anymore? This is new to me, if so that's perfect

 

[Vstromakias]

Oh so you don't even need the Magic NS anymore? This is new to me, if so that's perfect

Neighbor, I have tried ogx-mini and I can say that it works very well.

 

[XRed_CubeX]

Neighbor, I have tried ogx-mini and I can say that it works very well.

How much does it cost and where to buy?

 

[Vstromakias]

How much does it cost and where to buy?

https://www.melopero.com/shop/boards/pico/raspberrypipico/

https://www.melopero.com/shop/components/usbdiyconnectorshelltypeasocket/

 

[XRed_CubeX]

https://www.melopero.com/shop/boards/pico/raspberrypipico/

https://www.melopero.com/shop/components/usbdiyconnectorshelltypeasocket/

Cool, but does a regular Chinese USB extension cable work the same way for USB controller input?