Homebrew Constantly getting yellow screen when trying to launch homebrew now

[HikkiFan7]

So, now when I try to launch the homebrew channel it constantly hangs on the yellow screen and if I am able to launch the homebrew channel and try to launch for example Hans I always get the yellow screen.
What is going on?
It wasn't doing this less than an hour ago.

 

[SANNIC789]

maybe that game you're loading in hans is not compatible yet

 

[Pikm]

So, now when I try to launch the homebrew channel it constantly hangs on the yellow screen and if I am able to launch the homebrew channel and try to launch for example Hans I always get the yellow screen.
What is going on?
It wasn't doing this less than an hour ago.

What entrypoint, what firmware, what system?

 

[dpad_5678]

Make sure you use the most updated HANS.

 

[shaneod]

Everyone is focusing on this like it's a Hans issue, but isn't, based on how it's being described, but rather, it's a problem launching homebrew in general.

No idea, op.
I will say that I did have this issue or a similar issue recently, but can't remember how I fixed it.
What are you loading your homebrew through? Sysnand or emunand?

 

[MrMandraque]

Hello,
Your RAM is "full", (it's not that exactelly but...) push power button for 20 seconds (1 mississippi, 2 mississippi, etc...).
it happens to me very often when I run 2 or 3 applications following like RXtools, homebrew loader and gateway 3dsx, or gameyob and after 3dsFTP in CTRBoot Manager.

 

[HikkiFan7]

Everyone is focusing on this like it's a Hans issue, but isn't, based on how it's being described, but rather, it's a problem launching homebrew in general.

No idea, op.
I will say that I did have this issue or a similar issue recently, but can't remember how I fixed it.
What are you loading your homebrew through? Sysnand or emunand?

Emunand

 

[ih8ih8sn0w]

Emunand

What fw are you on for emunand, and is this n3ds or o3ds?

 

[HikkiFan7]

What fw are you on for emunand, and is this n3ds or o3ds?

10.3 o3ds

 

[ih8ih8sn0w]

10.3 o3ds

assuming you are using the cia launcher, try holding the button that forces the payload to download instead of launch immediately (im pretty sure its X) and hold Y to save the payload. also, try updating the boot.3dsx from the starter pack or grid launchers update feature if you are using that

 

[Funky.Art]

I'm upping this thread because i need help ! I have a New 3DS, and i installed Reinand, the last version, in 11.0E. But now, i can't use anymore Hans, on any game... I tried to use it from CtrBootManager, HB launcher in cia from the emunand, but Hans is always stucking at the yellow screen, no matter the game i launch...

 

[MrMandraque]

Hello,
It's very boring, you must modify the payload with an hex editor and rename boot.3dsx (homebrew loader) Like HBLB.3dsx per exemple or TOTO.3dsx.
µTuto:
connect your SD and rename boot.3dsx (homebrew loader) to bHBL.3dsx (in this exemple), keep CtrBootmanger's boot.3dsx.

in Left, Homebrew "channel". In right CTRBootManager.
Now search the payload : "/hblauncherloader_otherapp_payload_GENERATION-VERSION-SUBVERSION-XX-XX-COUNTRY.bin".
Like this:

Or Like this:

and open with HEX editor (GHex in my case).

Search boot.3dsx:



(offset 0000A0D7 here)
and replace boot.3dsx to bHBL.3dsx (or toto.3dsx, titi.3dsx, etc...) like this:


put you SD Card in your 3ds, boot to your CFW, launch hblauncherloader and PUSH IMMEDIATELY ON Y! ( see here)
tada!!!