1. dumbledore42

    OP dumbledore42 Member
    Newcomer

    Joined:
    Apr 7, 2018
    Messages:
    41
    Country:
    Germany
    Hello,
    i did the same thing like here in the video:
    After finishing installing cfw he clicks on launch and then CFW (SYSNAND). Minute 09:09
    I do the same but it opens the hekate menu and doesnt start my cfw sysnand?

    What am i doing wrong?
     
  2. Hayato213

    Hayato213 GBAtemp Guru
    Member

    Joined:
    Dec 26, 2015
    Messages:
    8,010
    Country:
    United States
    Don't follow sthetix video, he makes a lot of mistakes on his video, people end up bricking their unit, launch the fuse-primary.bin payload.
     
    dumbledore42 and Psyfurius like this.
  3. dumbledore42

    OP dumbledore42 Member
    Newcomer

    Joined:
    Apr 7, 2018
    Messages:
    41
    Country:
    Germany
    Thank you for the answer. How can i launch that? Do i have to do a new cfw?

    PS: when clicking on more configurations it says no .ini or boot files found in /bootloader/ini
     
    Last edited by dumbledore42, Dec 20, 2019
  4. Hayato213

    Hayato213 GBAtemp Guru
    Member

    Joined:
    Dec 26, 2015
    Messages:
    8,010
    Country:
    United States
    Newer build of Kosmos haven't been out you have to manual configure your CFW files for now, Atmosphere does support 9.1.0 firmware but Kosmos haven't been update with its CFW pack.
     
    Last edited by Hayato213, Dec 20, 2019
    dumbledore42 likes this.
  5. Psyfurius

    Psyfurius Member
    Newcomer

    Joined:
    Oct 4, 2019
    Messages:
    15
    Country:
    United States
    Download Fusee-Primary.Bin from Atmosphere GitHub and Inject it using TegraRcmGUI.
     
    dumbledore42 likes this.
  6. Lacius

    Lacius GBAtemp Legend
    Member

    Joined:
    May 11, 2008
    Messages:
    14,214
    Country:
    United States
    I recommend the following steps:
    1. Make a NAND backup with Hekate if you haven't already. Store it somewhere safe.
    2. Remove all CFW files/folders from your SD card (that would be folders like /sept/ and /atmosphere/)
    3. Download the latest Atmosphere from github
    4. Download the latest fusee-primary (next to Atmosphere)
    5. Download these signature patches
    6. Put Atmosphere and the signature patches onto your SD card
    7. Put the SD into your Switch
    8. Launch Atmosphere using fusee-primary
     
  7. dumbledore42

    OP dumbledore42 Member
    Newcomer

    Joined:
    Apr 7, 2018
    Messages:
    41
    Country:
    Germany
    I have already a nand backup with hekate.
    I want to do now a clean install from my cfw. How can i do that? delete the sd card?

    edit: I am trying what lacius said right now
     
    Last edited by dumbledore42, Dec 20, 2019
  8. Lacius

    Lacius GBAtemp Legend
    Member

    Joined:
    May 11, 2008
    Messages:
    14,214
    Country:
    United States
    Follow my steps above.
     
    dumbledore42 likes this.
  9. dumbledore42

    OP dumbledore42 Member
    Newcomer

    Joined:
    Apr 7, 2018
    Messages:
    41
    Country:
    Germany
    Thanks it worked.
    Why is it always so complicated on the internet? :wacko:
     
Draft saved Draft deleted
Loading...

Hide similar threads Similar threads with keywords - doesnt, hekate, start