1. sonique

    OP sonique Newbie
    Newcomer

    Joined:
    Mar 28, 2015
    Messages:
    8
    Country:
    United States
    Hi all, I've been using my switch with SX pro for a while, few days ago, I turned if off and it never turn back on. I connect it to my PC and found it was in RCM mode, however no matter which payload I sent it only shows black screen with backlight on. I tried different computer / sd card / cable, no luck.

    I followed the steps from "A definitive way to test if your Switch is patched or not (purchases after 07-2018)" and can confirm payload was successfully sent as the result screen shows 0X7000 as well as device keys.

    Do you guys think is there any way I can bring it back? Thanks!
     
  2. GCS

    GCS GBAtemp Fan
    Member

    Joined:
    Sep 10, 2020
    Messages:
    308
    Country:
    Turkey
    Have you tried hard resetting your Switch by holding down the power button for 15 seconds and then getting it into RCM mode to inject payload? If not, you can try that. If it doesn't work try if you can boot into OFW by holding the power button for 15 seconds and pressing it again.
     
  3. sonique

    OP sonique Newbie
    Newcomer

    Joined:
    Mar 28, 2015
    Messages:
    8
    Country:
    United States
    Just tried, same black screen with backlight on

    Unfortunately this doesn't work either :sad:
     
  4. GCS

    GCS GBAtemp Fan
    Member

    Joined:
    Sep 10, 2020
    Messages:
    308
    Country:
    Turkey
    Have you enabled Auto-RCM?
     
    Last edited by GCS, Oct 31, 2020
  5. sonique

    OP sonique Newbie
    Newcomer

    Joined:
    Mar 28, 2015
    Messages:
    8
    Country:
    United States
    I don't remember I did, but currently my switch went into RCM mode automatically without jig and holding button. The screen is black without back light.
     
  6. GCS

    GCS GBAtemp Fan
    Member

    Joined:
    Sep 10, 2020
    Messages:
    308
    Country:
    Turkey
    So, it's probably in AutoRCM, you can try this but can't guarantee if it will work:
    Click this, and click on the first video you see.
     
  7. sonique

    OP sonique Newbie
    Newcomer

    Joined:
    Mar 28, 2015
    Messages:
    8
    Country:
    United States
    Thanks, however my switch stay at black screen with backlight 2 hours after injection. I also tried to switch to charger but nothing happened :wacko:
     
  8. GCS

    GCS GBAtemp Fan
    Member

    Joined:
    Sep 10, 2020
    Messages:
    308
    Country:
    Turkey
    How much you waited for it to charge? At least 3 hours would be great.
     
  9. sonique

    OP sonique Newbie
    Newcomer

    Joined:
    Mar 28, 2015
    Messages:
    8
    Country:
    United States
    OK, I will leave it plugged for a few hour and report back, fingers crossed.
     
  10. GCS

    GCS GBAtemp Fan
    Member

    Joined:
    Sep 10, 2020
    Messages:
    308
    Country:
    Turkey
    And put it to charge after you close the switch fully(hold power button for 15 seconds.)
     
  11. sonique

    OP sonique Newbie
    Newcomer

    Joined:
    Mar 28, 2015
    Messages:
    8
    Country:
    United States
    Just checked my switch, same black screen after inject payload then switch to AC for 12 hours :wtf::wtf::wtf:
    The backlight kept on turoughout the whole process.
     
Draft saved Draft deleted
Loading...

Hide similar threads Similar threads with keywords - payload, inject, screen