Hacking Help won't on after downgrade

ThatFinn · Jun 10, 2020

I downgraded my switch and now I every time when is start my switch i get an error. So i disabled AutoRCM to start it normal but it didn't turn on. Please help me! There is the save files from my brother too. I don't know it so I have 2 hours then he is back and want play on my switch

Taorn · Jun 10, 2020

What error do you get?

If you downgraded farther then your fuse count allows, then it's no longer possible to boot normally, until you upgrade to a firmware version that your fuse count supports. You need to use a custom bootloader like Hekate or fusee-primary to boot.

Afaik if you downgraded to another major version, then you might need to reset your Switch. Although I'm not certain on that.

BaamAlex · Jun 10, 2020

The other question is, why did you downgrade your console? There is no reason to do that.

ThatFinn · Jun 10, 2020

Taorn i cannot boot into RCM and BaamAlex i want play Splatoon2 online without Nintendo switch online because after 8.1.0 you need Nintendo switch online to play Splatoon2 online.

Purple_Heart · Jun 10, 2020

if you dont have a clean nand backup and you used hacks (downgrading) then i wouldnt go online anyways ..BAN

BaamAlex · Jun 10, 2020

Finnlikecookies said:
Taorn i cannot boot into RCM and BaamAlex i want play Splatoon2 online without Nintendo switch online because after 8.1.0 you need Nintendo switch online to play Splatoon2 online.

Wat? Splatoon 2 doesn't need 8.1.0. And by the way, the rcm is always accessible.

Lacius · Jun 10, 2020

Finnlikecookies said:
Taorn i cannot boot into RCM and BaamAlex i want play Splatoon2 online without Nintendo switch online because after 8.1.0 you need Nintendo switch online to play Splatoon2 online.

Downgrading to 8.1.0 isn't going to allow you to play Splatoon 2 online for free. You can't play online at all unless you're on the latest system version, which is 10.0.4 as of this post.

What error are you receiving?

ThatFinn · Jun 10, 2020

I have modding the switch with sysnand make a backup from BOOT0, BOOT1, rawnand.bin My Question is how I can start my switch again. My brother is today not at home so i have more time.

Taorn · Jun 10, 2020

Finnlikecookies said:
I have modding the switch with sysnand make a backup from BOOT0, BOOT1, rawnand.bin My Question is how I can start my switch again. My brother is today not at home so i have more time.

How do you try to get into RCM mode?
Try using the original Switch USB3 cable in combination with TegraRcmGUI.
The program should show you if it can detect your Switch. Otherwise your battery might be flat.
Charge the Switch for a while and try again.

For more detailed advice you would need to provide more information on what procedure you followed to downgrade.
PS: If you want an answer, then quote people you're replying to. Otherwise they get no notification.

BaamAlex · Jun 10, 2020

Taorn said:
How do you try to get into RCM mode?

What a question...you don't have so much possibilities to get into the rcm my friend.

Lacius · Jun 10, 2020

Finnlikecookies said:
I have modding the switch with sysnand make a backup from BOOT0, BOOT1, rawnand.bin My Question is how I can start my switch again. My brother is today not at home so i have more time.

Did you restore your NAND and BOOT0/1 backups?

Taorn · Jun 10, 2020

BaamAlex said:
What a question...you don't have so much possibilities to get into the rcm my friend.

You will find that many people don't differentiate between shorting pin 10 and ground and then afterwards sending the payload. They will lump it together. No need to be pedantic about that. Besides there are quite a few methods to enter RCM, "friend".

So this question is basically aimed to get OP to tell how they tried to push the payload.

ThatFinn · Jun 11, 2020

I use already TegraRcmGUI and a USB3 cable. I can't boot into RCM after the downgrade. I charged the switch 10 hours and then i tried again to boot into Rcm. The switch screen is still black and my computer don't detect my switch so I'm not in Rcm. I tried to use another USB3 cable but it didn't work

BaamAlex · Jun 11, 2020

Are the drivers installed?

ThatFinn · Jun 11, 2020

Yes the problem is i can't boot into Rcm. My computer has no pro blem

BaamAlex · Jun 11, 2020

Then you do something wrong. Maybe the pins are not "correctly" shortened.

Finnlikecookies said:
every time when is start my switch i get an error

By the way, what is that for an error?

Lacius · Jun 11, 2020

Finnlikecookies said:
Yes the problem is i can't boot into Rcm. My computer has no pro blem

Specifically, how are you attempting to boot your Switch into RCM?

ThatFinn · Jun 11, 2020

I have a viedo from it: https://imgur.com/dSMRGnD
Sry for the bad quality

--------------------- MERGED ---------------------------

A viedeo how tried to boot into RCM

magico29 · Jun 11, 2020

Finnlikecookies said:
I have a viedo from it: https://imgur.com/dSMRGnD
Sry for the bad quality

--------------------- MERGED ---------------------------

A viedeo how tried to boot into RCM

We cant see it, are you using TegraRcmgui on your pc?

ThatFinn · Jun 11, 2020

Yes but that is not the problem

--------------------- MERGED ---------------------------

My Laptop can't detect my nintendo switch so my switch isn't in Rcm Mode.

Hacking Help won't on after downgrade

Well-Known Member

Well-Known Member

UDE GA NARU ZE!

Well-Known Member

GBATemp´s weirdest Individual

UDE GA NARU ZE!

Well-Known Member

Well-Known Member

Well-Known Member

UDE GA NARU ZE!

Well-Known Member

Well-Known Member

Well-Known Member

UDE GA NARU ZE!

Well-Known Member

UDE GA NARU ZE!

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Similar threads

Popular threads in this forum