Hardware Joycon no led's

warmo161 · May 14, 2019

Found out the other day my right joycon LED's stopped working, although when docked, the controller is fine. Did some googling and aperently its a known issue with one of the ribbon cables for the joycon rails

Why is it the switch has so many reliability issues? This is actually the second time im going to use the repair centre and they both for joycon problems

Are joycons made today any better than when the switch first came out? If so I was thinking on getting another pair (Apart from sending my broken one in)

mattytrog · May 14, 2019

warmo161 said:
Found out the other day my right joycon LED's stopped working, although when docked, the controller is fine. Did some googling and aperently its a known issue with one of the ribbon cables for the joycon rails

Why is it the switch has so many reliability issues? This is actually the second time im going to use the repair centre and they both for joycon problems

Are joycons made today any better than when the switch first came out? If so I was thinking on getting another pair (Apart from sending my broken one in)

Have you had them to bits? They don`t like being pulled those cables.

They normally snap a trace right at the end, where it goes into the FPC connector.

You can tin these exposed ends with solder... Just tin them - don`t blob them up... This CAN fix the broken trace by making the solder bridge the gap.

Your mileage may vary of course... But thats where they normally go.

Tin / reflow with solder, then put it back in the FPC. You won`t melt the cable. Its made to withstand soldering temperatures (ie like Kapton)

Simples.

warmo161 · May 14, 2019

mattytrog said:
Have you had them to bits? They don`t like being pulled those cables.

They normally snap a trace right at the end, where it goes into the FPC connector.

You can tin these exposed ends with solder... Just tin them - don`t blob them up... This CAN fix the broken trace by making the solder bridge the gap.

Your mileage may vary of course... But thats where they normally go.

Tin / reflow with solder, then put it back in the FPC. You won`t melt the cable. Its made to withstand soldering temperatures (ie like Kapton)

Simples.

Yes, i took it apart to attempt replacing the shell with a clear one, but its been closed up for over a year with no problems til now
Its the ribbon cable thats been folded and if you move it back it does still work but it isnt practical

mattytrog · May 14, 2019

warmo161 said:
Yes, i took it apart to attempt replacing the shell with a clear one, but its been closed up for over a year with no problems til now
Its the ribbon cable thats been folded and if you move it back it does still work but it isnt practical

Yeah they do fold. Are you sure its broken on the fold? I`ve seen failures on the "fold" but they normally split in half. They definitely don`t work then.

warmo161 · May 14, 2019

mattytrog said:
Yeah they do fold. Are you sure its broken on the fold? I`ve seen failures on the "fold" but they normally split in half. They definitely don`t work then.

Yep its definetly the fold (well i think anyways) it has line through where the fold is and giving it a wiggle and strightning it out, it works again (Ive had to take the joycon apart and replace the back shell and buttons back to stock for when I send it to repair)

Ive seen replacement rails on aliexpress but they dont look like complete parts so Im gonna avoid it if i can

mattytrog · May 14, 2019

warmo161 said:
Yep its definetly the fold (well i think anyways) it has line through where the fold is and giving it a wiggle and strightning it out, it works again (Ive had to take the joycon apart and replace the back shell and buttons back to stock for when I send it to repair)

Ive seen replacement rails on aliexpress but they dont look like complete parts so Im gonna avoid it if i can

I think, if it were me, I`d have a go at scraping the mask off the ribbon and tinning it.

warmo161 · May 14, 2019

mattytrog said:
I think, if it were me, I`d have a go at scraping the mask off the ribbon and tinning it.

I have no idea what that means, ill probably leave it for the moment and attempt to send it into nintendo
I can do basic soldering and stuff but i dont really want to break anything more than it is

Hardware Joycon no led's

Well-Known Member

You don`t want to listen to anything I say.

Well-Known Member

You don`t want to listen to anything I say.

Well-Known Member

You don`t want to listen to anything I say.

Well-Known Member

Similar threads

Popular threads in this forum