Hacking hekate+ atmosphere problem with SXcore

[lyokohack]

Hi all

I made a backup of my emunand and I want to check it under atmosphere

I have copied the fusee-primary.bin payload and I run it from hekate's Payload but nothing is displayed on my screen

 

[hartleyshc]

Hi all

I made a backup of my emunand and I want to check it under atmosphere

I have copied the fusee-primary.bin payload and I run it from hekate's Payload but nothing is displayed on my screen

I assume you have a patched v1 (Erista) Switch. If you don't, then it won't load.

If you do have a v1, then I think you need to run clean up from options in the SX Bootloader before you run Hekate from the payload button.

Sent from my ONEPLUS A6013 using Tapatalk

 

[JaRocker]

I assume you have a patched v1 (Erista) Switch. If you don't, then it won't load.

If you do have a v1, then I think you need to run clean up from options in the SX Bootloader before you run Hekate from the payload button.

Sent from my ONEPLUS A6013 using Tapatalk

I got the same problem and I have a patched v1 all other Payloads seems to work fine it’s just the fuess-primary.bin that’s not working

 

[hartleyshc]

I got the same problem and I have a patched v1 all other Payloads seems to work fine it’s just the fuess-primary.bin that’s not working

I was going to recommend a thread, but you've already posted there.

If I'm not too tired tonight, I'll try on my kids' modded Erista patched unit. They won't jump through the hoops of going to the payload menu for atmosphere. So I'm just waiting for a modchip firmware replacement before I swap them over to Atmosphere. But I'll go ahead and give it a shot see if I can write up some succinct instructions.

Sent from my ONEPLUS A6013 using Tapatalk

 

[DPyro]

I have same issue on Erista, V1 patched.

 

[lyokohack]

thank you for your part and for your clean up from options in the SX Bootloader

I am under sxosV3.0.4

at the beginning I did not modify this file "hekate_ipl.ini" I managed to launch it, I have this for my emunand



it's correct or not

but when I turn off my console switch , atmosphere he crash , I am using the latest fusee-primary.bin payload from
Atmosphère 0.15.0, but I use the data of my cfw atmosphere and i use this hekate ctcaer v5.3.3 version

I can not make work this link https://www.sdsetup.com, it tells me that I need to deactivate my antivirus, and I do not know what to do

 

[JaRocker]

I was going to recommend a thread, but you've already posted there.

If I'm not too tired tonight, I'll try on my kids' modded Erista patched unit. They won't jump through the hoops of going to the payload menu for atmosphere. So I'm just waiting for a modchip firmware replacement before I swap them over to Atmosphere. But I'll go ahead and give it a shot see if I can write up some succinct instructions
Sent from my ONEPLUS A6013 using Tapatalk

I can’t wait for the modded modchip firmware it wouldn’t be that big of a deal of tx didn’t make the bootloader so shitty

 

[DragarX]

I've only been able to boot Atmosphere though Hekate, I don't think is possible to boot fusee primary directly from sx menu.

 

[hartleyshc]

So here's how I did it. I only booted to Atmosphere sysnand just to test. I'm not sure how to go and set up emummc, as Hekate didn't detect my SX emunand.

Patched Erista, SX Core fw 1.3, FW 10.2.0

Downloaded Hekate from it's github. Latest version.
Downloaded Atmosphere from it's github. Latest version. Along with the fusee-primary.bin file.

Extracted everything and copied to the sd card. Copied the fuses-primary.bin file to sd:/bootloader/payloads folder.

Held down volume up and powered on the system. Went to options, sx core, cleanup. Went to payloads and loaded hekate. Hekate asked for date and time, filled it out, then went to payloads within Hekate and selected fusee-primary.bin

Atmosphere then loads in sysnand. I verify its working by going to album and hbmenu loads. All homebrew previously on the card loads. Back out and do the title launch to load hbmenu again and go to retroarch. Run a couple of games to test. All works well.

Sent from my ONEPLUS A6013 using Tapatalk

 

[JaRocker]

I've only been able to boot Atmosphere though Hekate, I don't think is possible to boot fusee primary directly from sx menu.

I got it working seems like sx made changes to the boot0 and boot1 that’s what’s stopping atmosphere from booting from Fuess primary So I made a clean boot0 and boot1 for the version that I’m running then use them to replace the once’s on my emunand,
Tested booting from Hekate and sx boot menu both work fine

--------------------- MERGED ---------------------------

So here's how I did it. I only booted to Atmosphere sysnand just to test. I'm not sure how to go and set up emummc, as Hekate didn't detect my SX emunand.

Patched Erista, SX Core fw 1.3, FW 10.2.0

Downloaded Hekate from it's github. Latest version.
Downloaded Atmosphere from it's github. Latest version. Along with the fusee-primary.bin file.

Extracted everything and copied to the sd card. Copied the fuses-primary.bin file to sd:/bootloader/payloads folder.

Held down volume up and powered on the system. Went to options, sx core, cleanup. Went to payloads and loaded hekate. Hekate asked for date and time, filled it out, then went to payloads within Hekate and selected fusee-primary.bin

Atmosphere then loads in sysnand. I verify its working by going to album and hbmenu loads. All homebrew previously on the card loads. Back out and do the title launch to load hbmenu again and go to retroarch. Run a couple of games to test. All works well.

Sent from my ONEPLUS A6013 using Tapatalk

If you would like to use your sxos emunand with hekate you can use this config but it only works with the Hidden partition I haven’t been able to get a working config for the sd files I’ll try to work on that at a later date.
[emummc]
enabled=1
sector=0x2
path=Emutendo
id=0x0000
nintendo_path=Emutendo

 

[DPyro]

How do you replace them on emunand partition?

 

[JaRocker]

How do you replace them on emunand partition?

you can do it via NxNandManager https://github.com/eliboa/NxNandManager/tags
just inside the SD card with a hidden partition into your PC and use NxNandManager it will be able to find the hidden partition.
if you're not familiar with this process I would suggest you make a backup before doing anything this tool can also be used to make backups of your nand and mush more
if you need a clean boot0 and boot1 you use EmmcHaccGen to make them
https://github.com/suchmememanyskill/EmmcHaccGen/tags

 

[britain4]

Same problem here, good to know there’s a fix. I’m happy enough using Hekate with it rather than fusee-primary as that works fine but glad it’s not just me

 

[OrGoN3]

thank you for your part and for your clean up from options in the SX Bootloader

I am under sxosV3.0.4

at the beginning I did not modify this file "hekate_ipl.ini" I managed to launch it, I have this for my emunand



it's correct or not

but when I turn off my console switch , atmosphere he crash , I am using the latest fusee-primary.bin payload from
Atmosphère 0.15.0, but I use the data of my cfw atmosphere and i use this hekate ctcaer v5.3.3 version

I can not make work this link https://www.sdsetup.com, it tells me that I need to deactivate my antivirus, and I do not know what to do

You do realize the picture you attached is of your sysnand, and not your emunand, right? That's why it ends with an 'S' and not an 'E'.

 

[lyokohack]

You do realize the picture you attached is of your sysnand, and not your emunand, right? That's why it ends with an 'S' and not an 'E'.

thank you for your answer to my question

because I did not create my emunand under hekate , because I didn't know at first

I have directly copy the files to my disk, because I have a 32gb card and I have to copy my files twice

I search to find Hekate + Atmosphere package , because i don't find this package

 

[DPyro]

I did try NxNandManager but it didn't find a partition.

EDIT: Nevermind, I needed to double click SD card.

 

[DPyro]

Is there a tutorial how to generate boot ising EmmcHaccGen?

 

[JaRocker]

Is there a tutorial how to generate boot ising EmmcHaccGen?

Glad you got it working I’ll try to remember to send you the Commands for when I get home EmmcHaccGen

 

[lyokohack]

I tried to make the sdSetup website work for a while, I only downloaded hekate and atmosphere
then when I run SysNAND (CFW) from hekate I have this message has it with the start logo

Pk92 descryption failed!

failed to lanch HOS!

then i noticed when starting sx os that my console switch patched marks this = Erista

 

[JaRocker]

I tried to make the sdSetup website work for a while, I only downloaded hekate and atmosphere
then when I run SysNAND (CFW) from hekate I have this message has it with the start logo

Pk92 descryption failed!

failed to lanch HOS!

then i noticed when starting sx os that my console switch patched marks this = Erista

I’m not sure what your asking for help with but if you need a easy cfw pack that comes with hekate you can use deepsea cfw pack https://github.com/Team-Neptune/DeepSea/releases/tag/v1.8.1
If you don’t want or need the extra stuff that comes with it just you the minimal version