i already has rxtools in that systemAnymore details?
Like does it boot to emuNAND?
CFW?
Is it right after installing a9lh from homebrew?
which one should i restore ?You could try checking if you have all the firmware bins
https://github.com/Plailect/Guide/wiki/Part-3-(EmuNAND)
Worst case, just use decrypt9 to restore a sysNAND backup
How did you get the sysNAND-A9LH if you werent able to boot to sysNAND after the a9lh...? Directly from a9lh boot to D9?which one should i restore ?
sysNAND-A9LHAX.bin or sysNAND.bin (the original one) ?
in the part 5 i made a backup of sysnand then pressed select and got the SD card and rename it to sysNAND-A9LHAX.binHow did you get the sysNAND-A9LH if you werent able to boot to sysNAND after the a9lh...? Directly from a9lh boot to D9?
You could restore the original and try again
in the part 5 i made a backup of sysnand then pressed select and got the SD card and rename it to sysNAND-A9LHAX.bin
now i restore it and i can load sysnand if i press any button ( i have menuhax installed on 9.2 so i have to press any button to prevent from launching homebrew channel )
i don't know what the difference now , did i succeeded ?
at first i tried restore the original and it wont boot upIf you restored the original, you'll need to run the a9lh.3dsx again to install the a9lh
at first i tried restore the original and it wont boot up
but then i restored sysNAND-A9LHAX.bin and i can boot up normally
how i can tell if that sysnand is modded ?
i thought this whole process will give me much faster speed boot with no error
but in the end if part 5 i found it replace emunand with sysnand ? is that right ?
if i press X i boot to decrypt9WIB
if i press Y i boot to emunand9
if i press L i boot to cake 138 menu
this is why im staying clear of a9lh for now.
oh, then i think i restored the original nandTry booting Decrypt9 and cake menu.
If you can, then the a9lh is there
Try booting Decrypt9 and cake menu.
If you can, then the a9lh is there
--------------------- MERGED ---------------------------
oh, then i think i restored the original nand
that's 5 hours is wasted.
really? thanks for the info ill keep that in mindTry booting Decrypt9 and cake menu.
If you can, then the a9lh is there
--------------------- MERGED ---------------------------
a9lh is fine, its just that the new updated guide makes you do everything on sysnand, which is technically more "unsafe" if you were to mess anything up.
The old guide used AuReiNand which sets everything up on emuNAND and autoboots to emuNAND. You could optionally switch the emuNAND and sysNAND if you wanted to later on.
really? thanks for the info ill keep that in mind
the emunand route sounds safer messing with sysnand was my turn away.Well, getting the OTP process is set as is, which is tedious if you don't read and follow the guide carefully.
What changed was which CFW you use with the a9lh and how you set up your system thereafter.
if all that happened is on and off within a second with a9lh, then you did everything right in the first place. you just needed the a9lh.bin file for your cfw. these people misled youi managed to capture what that message trying to say
"Mounted SD card
Loaded config file
Autobooting...
Booting FIRM..."
then nothing
Not as familiar with CakesFW if you're currently using it.i managed to capture what that message trying to say
"Mounted SD card
Loaded config file
Autobooting...
Booting FIRM..."
then nothing
yes, it was less then secondif all that happened is on and off within a second with a9lh, then you did everything right in the first place. you just needed the a9lh.bin file for your cfw. these people misled you