Short Version: Trying to do a new Ninjhax 1 install on an old 3DS, I run it, it gets to 40% and then it loads the internet browser and freezes.
OK I'm on an old 3DS. I updated it to 8.1.0-10U using the game LEGO Ninjago Shadow of Ronin. I use Cubic Ninja to install Ninjahx 1 (http://smealum.net/ninjhax/)
I have installed Ninjhax 1 on many 3DSs before so I am pretty sure I am doing nothing wrong. I have even installed Ninjahx 1 on this specific 3DS before and it worked fine! Back then it was on version 6. something, I have since updated this 3DS to 8.1 as I said above.
Unfortunately I do not have another 3DS to test if it is something on my end or if smealums payloads are down or something.
I note that on his page (http://smealum.net/ninjhax/) one of the Q&As says this:
But I know I am definitely using the correct QR code! So it must be something else. I realize smealum is probably a busy person so instead of trying to email him like it says I am trying here first. I type in 8.1.0-10U exactly. I have tried it dozens of times to make sure. I even went so far as to try with the QR code backups from that reddit site.
I've tried completely factory resetting the 3DS and reformatting the SD card. Nothing works.
I do always clear the Cubic Ninja save. (Like I said, I have installed on several 3DSs before, and I am doing the exact same steps I always do.)
Normally when ninjhax runs on a 3DS I see it go from 20% to 40% then to 100% then the HBC loads. (I believe after 40% is when it downloads the payload from smealums site.)
But on this 3DS, since yesterday, as soon as it gets to 40% the internet browswer pops up and the 3DS freezes.
I'm going to be away for a few hours so I hope I didn't leave out any info. (I have a feeling that the first response is going to be "smealums payloads are offline".)
The only other thing I can think of is it has something to do with me using that game to update to 8.1.0-10U. But that doesn't really make sense.
Thanks ahead of time for any help.
OK I'm on an old 3DS. I updated it to 8.1.0-10U using the game LEGO Ninjago Shadow of Ronin. I use Cubic Ninja to install Ninjahx 1 (http://smealum.net/ninjhax/)
I have installed Ninjhax 1 on many 3DSs before so I am pretty sure I am doing nothing wrong. I have even installed Ninjahx 1 on this specific 3DS before and it worked fine! Back then it was on version 6. something, I have since updated this 3DS to 8.1 as I said above.
Unfortunately I do not have another 3DS to test if it is something on my end or if smealums payloads are down or something.
I note that on his page (http://smealum.net/ninjhax/) one of the Q&As says this:
ninjhax won't run at all ! It is freezing at 70% or opening the web browser for some reason. What am I doing wrong ?
This most likely means you are using the wrong QR code for your console/firmware version. Please double check that you are using the correct version. If the problem persists, let me know my sending me an email at
But I know I am definitely using the correct QR code! So it must be something else. I realize smealum is probably a busy person so instead of trying to email him like it says I am trying here first. I type in 8.1.0-10U exactly. I have tried it dozens of times to make sure. I even went so far as to try with the QR code backups from that reddit site.
I've tried completely factory resetting the 3DS and reformatting the SD card. Nothing works.
I do always clear the Cubic Ninja save. (Like I said, I have installed on several 3DSs before, and I am doing the exact same steps I always do.)
Normally when ninjhax runs on a 3DS I see it go from 20% to 40% then to 100% then the HBC loads. (I believe after 40% is when it downloads the payload from smealums site.)
But on this 3DS, since yesterday, as soon as it gets to 40% the internet browswer pops up and the 3DS freezes.
I'm going to be away for a few hours so I hope I didn't leave out any info. (I have a feeling that the first response is going to be "smealums payloads are offline".)
The only other thing I can think of is it has something to do with me using that game to update to 8.1.0-10U. But that doesn't really make sense.
Thanks ahead of time for any help.