1. psycoblaster

    OP psycoblaster Divine
    Member

    Joined:
    Jan 26, 2008
    Messages:
    2,131
    Country:
    a failed post does not exist in a failed thread
     
  2. delta123

    delta123 GBAtemp Advanced Fan
    Member

    Joined:
    Jul 18, 2005
    Messages:
    576
    Country:
    if you have custom firmware then you can use it to make a pandora battery for use to install the firmware onto your psp. after that you can switch it back to a normal battery if you save the code from the battery.
     
  3. Originality

    Originality Chibi-neko
    Member

    Joined:
    Apr 21, 2008
    Messages:
    5,706
    Country:
    Read the other topics. Pandora batteries can either be soft-modded with Despartar Del Cementario or other Pandora-making programs, or it can be hard-modded (cutting a connector on the chip).

    To restore it, depending on your method, you either softmod back its IPL, or you solder back the chip connection (using a copper wire in place will do the trick).

    EDIT: Pandora batteries are used to downgrade quickly and efficiently to v1.5 on the PSP Phat (on slim, it installs CFW 3.90 straight). v1.5 lets you run any application, and you can upgrade from there just by running the EBOOT.PHP of the CFW.
     
  4. Shyn

    Shyn GBAtemp Regular
    Member

    Joined:
    Sep 10, 2006
    Messages:
    184
    Country:
    United States
    http://www.psp-hacks.com/2007/10/22/one-wi...tware-required/

    Two solder point method. If you get a piece of wire to run between the two points on the picture, instead of soldering it down, tape it with clear tape to the points. Make sure to tape off any other part of the wire that may touch something else to avoid problems. Once done, just take off the wire and tape up the battery and it will be fully functional.
     
  5. psycoblaster

    OP psycoblaster Divine
    Member

    Joined:
    Jan 26, 2008
    Messages:
    2,131
    Country:
    a failed post does not exist in a failed thread
     
  6. Shyn

    Shyn GBAtemp Regular
    Member

    Joined:
    Sep 10, 2006
    Messages:
    184
    Country:
    United States
    The two red boxes are the soldering points. Get a very small piece of copper wire and get the two ends to touch the two points (red boxes).
    Yes, any clear or scotch tape will work, I used clear tape because it was easy to take on and off without leaving any residue. I also wrapped any part of the wire that would touch the main board up with tape as well, to prevent any possible problems. Once you are done putting the wire in place, it is a pandora's battery. After you are done using it, just remove the wire, and it is back to a regular battery.

    If you are considering using this method, I can take some pictures of what I did, but I have a PSP Slim, and the batteries are different. The method is the same, but it is just running it between two different points.
     
  7. warmijwilfaain

    warmijwilfaain War Mage MILF
    Member

    Joined:
    Sep 30, 2007
    Messages:
    1,310
    Country:
    Or you could just buy a Datel TOOL battery. Whatever, really.
     
  8. Shyn

    Shyn GBAtemp Regular
    Member

    Joined:
    Sep 10, 2006
    Messages:
    184
    Country:
    United States
    Yeah, but why waste more money, when you can just use some stuff you already have. I personally chose to mod a normal battery over buying a TOOL battery because now I have a spare.
     
  9. psycoblaster

    OP psycoblaster Divine
    Member

    Joined:
    Jan 26, 2008
    Messages:
    2,131
    Country:
    a failed post does not exist in a failed thread
     
  10. Shyn

    Shyn GBAtemp Regular
    Member

    Joined:
    Sep 10, 2006
    Messages:
    184
    Country:
    United States
    I'm sure it would work on a phat battery as well as it does on the slim batteries. I don't know exactly how it works, but I do know it works.

    Here's a couple pictures to show the wire I used. I'm sorry the pictures are blurry, but my camera is kind of old and the light in my room is bad.
    I put the wire next to a dime to show the size of it.
    [​IMG]
    [​IMG]
     
  11. psycoblaster

    OP psycoblaster Divine
    Member

    Joined:
    Jan 26, 2008
    Messages:
    2,131
    Country:
    a failed post does not exist in a failed thread
     
  12. suppachipmunk

    suppachipmunk GBAtemp Fan
    Member

    Joined:
    Jan 14, 2007
    Messages:
    400
    Country:
    United States
  13. Shyn

    Shyn GBAtemp Regular
    Member

    Joined:
    Sep 10, 2006
    Messages:
    184
    Country:
    United States
    I think what happens is that when you cut the leg on the chip, the chip switches to a different circuit. This method just creates that circuit, so the result is the same. Originally you would have to solder the wire into place, onto the points, but I figured out that taping the wire into place works too, just that you have to make sure the wire is secure to the points.
     
  14. psycoblaster

    OP psycoblaster Divine
    Member

    Joined:
    Jan 26, 2008
    Messages:
    2,131
    Country:
    a failed post does not exist in a failed thread
     
  15. Shyn

    Shyn GBAtemp Regular
    Member

    Joined:
    Sep 10, 2006
    Messages:
    184
    Country:
    United States
    Exactly.
     
  16. psycoblaster

    OP psycoblaster Divine
    Member

    Joined:
    Jan 26, 2008
    Messages:
    2,131
    Country:
    a failed post does not exist in a failed thread
     
  17. Shyn

    Shyn GBAtemp Regular
    Member

    Joined:
    Sep 10, 2006
    Messages:
    184
    Country:
    United States
    Yep, you got the basics down for the battery. As far as PSP Grader goes, you will need to get the 1.5 and 3.80 eboots, which a google search of "All update eboots" will get you.
     
Draft saved Draft deleted
Loading...

Hide similar threads Similar threads with keywords - installing,