Hacking RELEASE [Official] ReiNX thread [DEAD]

[Adran_Marit]

I'm just using the legacy files, no hbl.nsp. I've tried other combinations, that's all I was saying. Still, hbl-config.ini doesn't seem to be doing anything. I've seen posts in this thread about hbl-config.ini being ignored, maybe that's what's happening? Didn't seem to see any solution to those posts though. Maybe it's an nx-hbloader issue? Either way I've now got a workaround opening the homebrew menu without hbloader, so don't worry about me.

did you use the replacement ones I linked?

 

[localmachine]

did you use the replacement ones I linked?

Yup, from post #2570. Selecting the album opens the homebrew menu, holding R opens the album normally, regardless of what I do to hbl-config.ini.

 

[Adran_Marit]

Yup, from post #2570. Selecting the album opens the homebrew menu, holding R opens the album normally, regardless of what I do to hbl-config.ini.

That's the intended behavior of it. The config is ignored in later versions of reinx as main override behavior is now set in the sysmodules now as they are now required on later firms due to sept and secmon

 

[noneedf0raname]

The latest commit of ReiNX should have already addressed that. Just replace the ReiNX files you're using with the latest available.

I’m having the unable to start software issue too, but I’m not sure what you mean by this. How can I fix the issue?

 

[localmachine]

That's the intended behavior of it. The config is ignored in later versions of reinx as main override behavior is now set in the sysmodules now as they are now required on later firms due to sept and secmon

Ouch, wish reinx.guide said something about that before I did all this messing around. So no way to launch the homebrew menu with anything but the album? Also ouch.

 

[Adran_Marit]

Ouch, wish reinx.guide said something about that before I did all this messing around. So no way to launch the homebrew menu with anything but the album? Also ouch.

You change the folder name afaik.

so lets say you want it to be eshop instead you change the floder id to that of the shop

I’m having the unable to start software issue too, but I’m not sure what you mean by this. How can I fix the issue?

Get the latest build from the guide even if you already have 2.2.1 get it again and delete your old files and replace them. If you still have an issue send a message on the discord

 

[Dothackjhe]

The version 2.2.1 of ReiNX did get twice a revision I think, but only managed to retain the naming.

 

[hippy dave]

The version 2.2.1 of ReiNX did get twice a revision I think, but only managed to retain the naming.

Wow, so much like atmosphere!

 

[PandFurr]

Well Legacy method don't work for me i don't have hbl-config.ini in my sd idk where i found it

 

[Adran_Marit]

Well Legacy method don't work for me i don't have hbl-config.ini in my sd idk where i found it

remove hbl.nsp from /reinx if its there and use these legacy files

HBL Legacy

 

[PandFurr]

remove hbl.nsp from /reinx if its there and use these legacy files

HBL Legacy

I remove the hbl.nsp but. Nothing happens still boot the Homebrew even If I have the legacy files

 

[Adran_Marit]

I remove the hbl.nsp but. Nothing happens still boot the Homebrew even If I have the legacy files

Hold r to access album with them. Make sure to do a clean install of legacy as well

 

[PandFurr]

Hold r to access album with them. Make sure to do a clean install of legacy as well

I do a clean install I hold r and nothing still enter to hbl

 

[charlieb]

That's the intended behavior of it. The config is ignored in later versions of reinx as main override behavior is now set in the sysmodules now as they are now required on later firms due to sept and secmon

Can you explain how to keep/enable nogc in the latest version?

This is often skipped in guides as is not too clear on how to enable it in the lastest verison

 

[Adran_Marit]

I do a clean install I hold r and nothing still enter to hbl

Chuck a message on the discord then if you are still having issues

Can you explain how to keep/enable nogc in the latest version?

This is often skipped in guides as is not too clear on how to enable it in the lastest verison

NoGC is only really used if your fuses are still below 5 burned fuses, but to enable it you make a blank file called nogc in the reinx folder or use the latest version of the toolkit to enable nogc

 

[Geekyrulez]

The version 2.2.1 of ReiNX did get twice a revision I think, but only managed to retain the naming.

Wow I downloaded twice from github only to waste many hours pondering that one. I will try downloading from the guide. However it's a lot better if the official channel gets proper release.

 

[Adran_Marit]

Wow I downloaded twice from github only to waste many hours pondering that one. I will try downloading from the guide. However it's a lot better if the official channel gets proper release.

The github got stealth updated as well from what I know.

but the guide or discord is always the best place to get builds from

 

[Imancol]

Add EmuNand Support, and XCI mount USB Loader

 

[Adran_Marit]

Add EmuNand Support, and XCI mount USB Loader

If you look at previous commits reinx actually supports some of the rommenu functions at present.

I think emunand is still somewhere in the works as well.

 

[karYzan]

In system it says im running 8.0.1 ReiNX but I can't get the homebrew menu to start in anyway.
The album just starts normally.