luma cfwsysnand and dstwo

Discussion in '3DS - Flashcards & Custom Firmwares' started by binx2469, May 26, 2016.

  1. binx2469
    OP

    binx2469 Member

    Newcomer
    16
    0
    Aug 13, 2011
    Hi, I`ve followed plailects guide and now have a cfwsysnand on v11. Is there a way to use my supercard dstwo on this nand? I can see the icon for it but when booting it just blackscreens. Any advice would be greatly appreciated.
     
  2. Swiftloke

    Swiftloke Hwaaaa!

    Member
    1,770
    1,516
    Jan 26, 2015
    United States
    Nowhere
  3. Robz8

    Robz8 Coolest of TWL

    Member
    6,693
    2,828
    Oct 1, 2010
    United States
    If you have emuNAND, boot it from there.
     
  4. binx2469
    OP

    binx2469 Member

    Newcomer
    16
    0
    Aug 13, 2011
    Thanks for the reply. I currently don'thave an emunand setup. Will the cart work from a v11 emunand or will it have to be v9.2. I have backups of 9.2 emunand. Could I create a new emunand from that. I was hoping there was a way to launch from sysnand to make it easy for small children to use. Thanks again for the help
     
  5. Robz8

    Robz8 Coolest of TWL

    Member
    6,693
    2,828
    Oct 1, 2010
    United States
    If you have A9LH, you don't need emuNAND.
     
  6. binx2469
    OP

    binx2469 Member

    Newcomer
    16
    0
    Aug 13, 2011
    I have a9lh installed and am currently booting into v11 Luma sysnand. From there my dstwo black screens.
     
  7. Rioluwott

    Rioluwott GBAtemp Advanced Fan

    Member
    646
    91
    Feb 23, 2014
    Mexico
  8. TamDanny

    TamDanny GBATemp 3DS Fanatic

    Member
    314
    215
    Aug 20, 2015
    Mexico
    I don't know about you, but i got my DSTwo working perfectly fine with A9LH.

    I got N3DSXL updated sysNAND 11.0 with a Luma3DS nightly (not latest, but more recent than Luma 5.4). Probably best to check that Troubleshooting link above. ^
     
  9. binx2469
    OP

    binx2469 Member

    Newcomer
    16
    0
    Aug 13, 2011
    Thanks for the link. I'm not near a PC at the moment but will definitely try when I get home. Its good to hear that supercard will work with a9lh Lima sysnand on v11

    edit Thanks for the help. I`ve installed a new agb/twl firm and everything is working now.
     
    Last edited by binx2469, May 27, 2016
  10. Timburpton

    Timburpton GBAtemp Advanced Fan

    Member
    591
    133
    Nov 18, 2014
    How did you get it working? Ctrboot? Or the gateway.cia?
     
  11. TamDanny

    TamDanny GBATemp 3DS Fanatic

    Member
    314
    215
    Aug 20, 2015
    Mexico
    It just worked. I put the card in, and it's starts up fine when I open it on the home menu. I didn't add or install anything new to get it to work. It's to my knowledge that Luma applies the patches automatically, but even so, this was working before A9LH & emuNAND.
     
  12. Temptress Cerise

    Temptress Cerise Miss Magic~ <3

    Member
    2,181
    1,421
    May 1, 2016
    United States
    DSTwo should work even on a stock system. I know, I actually have tested it out on a clean//vanilla//stock 11.0 system, and it booted up just fine. Check to make sure you have all the correct files for your DSTwo on the DSTwo's memory.
     
  13. Quantumcat

    Quantumcat Dead and alive

    Member
    10,449
    5,514
    Nov 23, 2014
    Australia
    Canberra, Australia
    Mine works fine in Luma mode too.