Hacking Help with setting up emunand

[hab]

I had Rxtools woorking when trying to get the OPT file it stop working.
Trying to start over with Cakes or
AuReiNand [N3DS/O3DS/A9LH] to setup or load emunand but all i get is a black screen.
Please help ?

 

[naivegirl2411]

I had Rxtools woorking when trying to get the OPT file it stop working.
Trying to start over with Cakes or
AuReiNand [N3DS/O3DS/A9LH] to setup or load emunand but all i get is a black screen.
Please help ?

CFW has a crappy boot rate (be it aureinand, cakes, pasta, etc). Since youre probably trying to get arm9lh installed with your otp is doesnt really matter what cfw you use as long as you can boot into emunand to proceed with your OTP/ARM9LH installation. I have an o3ds which was on 9.2 when I tried this and the only CFW that I had luck in booting with was rxtools which was set up using this guide:
https://gbatemp.net/threads/tutorial-installing-rxtools-custom-firmware-3ds-and-2ds.390867/

I had to hit x immediately after clicking on it in homebrew to get it to load. Once I was done getting my otp I followed the rest of this guide

https://github.com/Plailect/Guide/wiki

and switched to aureinand + arm9lh. Just remember to also check the otp helper thread for any info on new releases and which one you need to use (it makes a huge difference which version you use)

https://gbatemp.net/threads/release-otphelper-otp-dumping-downgrade-helper.416996/

 

[hab]

Working on getting Rxttols to boot but bottom screen in black?

 

[naivegirl2411]

Odd... Just the bottom screen? When I booted into rxtools cfw I pressed x immediately which displayed the rxtools splash screen on the top screen and around 5-8 seconds later the home menu appeared which means that I am in cfw. You can check if youre in by going into system settings and checking the system fw version but know that once you exit system settings you exit cfw and have to enter it again via hbl, etc

 

[hab]

there was some data folder delete it now cfw is setup
Aare tou willing to help me setup otp stet btystep?

--------------------- MERGED ---------------------------

should i use RXTOOLS 3.0 beta 2 or nightly or 2.6?

 

[naivegirl2411]

there was some data folder delete it now cfw is setup
Aare tou willing to help me setup otp stet btystep?

If it wasnt 10:30pm on my side I might be able to but as it takes a lot of time (a good few hours) I wont be able to. Read through these guides:

1: For emunand setup and basic understanding of what youre doing https://gbatemp.net/threads/tutorial-installing-rxtools-custom-firmware-3ds-and-2ds.390867/
2: The complete otp+arm9lh guide https://github.com/Plailect/Guide/wiki

If you read them well and understand homebrew launcher entry points you will be fine. Its all about reading and understanding. If youre unsure and want to wait a bit longer you can try keeping emunand as its basically doing the same thing. It is a risky process and I had a few scares when I set it up so you have to decide if you need it or not

 

[hab]

OK RXTOOLS launch how do i change the backroard just on emu?

 

[hab]

10.7 on rxtools

 

[hab]

ok have both Rxtools and
AuReiNand v 3.10 working but now oot hack just bot to
AuReiNand v3.10 what did i do wrong i trying to inject fbi to keep going?

 

[hab]

ok have otp fine re setup 9.2 and emu but when i try to load rxtools is just freezes at the top screen with rxtool bottom screen black ?
Should i try the tiny format on emu to format is over?

 

[hab]

RXtools is all setup now