Hacking SWITCH NOOB PARADISE - Ask questions here

[Mrzio]

No worries. In that case a modchip is you only option to hack. 7.0.1 isn’t that special. You will get more out of your switch if you upgrade.

if your game card is not reading latest games then maybe it is something that can be fixed with a firmware update. However, if your switch stopped reading game cards that used to work (and a tech said you need an IC replaced) that’s a different issue and and a hardware problem that can’t be fixed by updating firmware. You should get your hardware fixed first.

He fixed the switch that had an ic problem that made it not turn on, but now using it i noticed that it doesn't reads the game cards and make the notification that u can see in the photo i attached in my first post here

 

[PokeGen]

Im currently looking for homebrew that would allow me to remotely connect to my switch from my PC. Basically play the Switch on PC. Can someone help me out here? Thanks!

 

[binkinator]

He fixed the switch that had an ic problem that made it not turn on, but now using it i noticed that it doesn't reads the game cards and make the notification that u can see in the photo i attached in my first post here

Here is the translated image. Seems that the card reader is having issues.

very similar to this error:

See if any of these solutions help:

https://appuals.com/nintendo-switch-game-card-error/

Post automatically merged: Oct 22, 2022

Im currently looking for homebrew that would allow me to remotely connect to my switch from my PC. Basically play the Switch on PC. Can someone help me out here? Thanks!

https://github.com/exelix11/SysDVR will get the graphics on your PC screen. The controls would still be via the switch though.

 

[grooster]

In the past, I could press "B" to exit hbmenu. That isn't working now. Is there a setting to make it exit that way?

 

[Klavice Gavin]

When I open hekate on my Switch, it keeps saying it's in 1bit mode. Which is funny because it reads the card no problem at least NOW it does and I haven't had this issue until just recently nor have I done anything to the pins. I'd open it up if to check if I could but I don't even know what screwdriver the Switch uses and I'm afraid of damaging my Switch.
This has happened ever since i upgraded to 14.1.2 and then 15.0.0 and while my Switch works normally otherwise, I'm getting more worried by the minute. It happened with my 1TB SD Card all of a sudden and before that It never happened with any prior cards. The card is Sandisk too. I think it's an issue with the sigpatches as I just installed them.
Update: I tried a rather unorthodox solution by searching the forum and found that if I apply pressure to the sd card reader it will sometimes go past the original check. Unfortunately this leads to other problems, like my Switch not wanting to accept hekate, and I feel like I've exhausted every possibility besides taking it apart, and I really don't want to do that. I just know some people said on this forum that if the pins are even slightly loose it can mess things up big time. As I said this is ONLY when trying to use CFW, everything else works perfectly.

 

[GravityLoL]

This is the way I do it:

https://nh-server.github.io/switch-guide/extras/transfer_sd/

Problem is, i don't have enough free space on my SD card. Is there some other method that requires using only PC for backup?

 

[Bestio94]

Hello everyone,
I downgrade my switch from 14.1.2 to 4.1.0 using daybreak on my sysnand to unlock the possibility of use pegascape.
Now my switch don't boot up anymore, I can only launch hakate from RCM.
I have no backup...
Anyone can help me?

 

[grooster]

Problem is, i don't have enough free space on my SD card. Is there some other method that requires using only PC for backup?

What OS are you using? For Windows, maybe consider something like NIUBI Partition Editor.

That will let you copy, resize and move partitions around.

 

[GravityLoL]

What OS are you using? For Windows, maybe consider something like NIUBI Partition Editor?

That will let you copy, resize and move partitions around.

yeah, i'm on Windows. So that NIUBI stuff will do the work?
I don't want to somehow break up my SD Cards so i'm little nervous about it

 

[grooster]

yeah, i'm on Windows. So that NIUBI stuff will do the work?
I don't want to somehow break up my SD Cards so i'm little nervous about it

I'm not sure what you mean about "break up" but this is standard stuff. You're copying to a new SD card, right? It would be a lot easier if you used file-based emuNAND. You should be able to copy the partition and I think the system would still find it but I haven't tested it. You may want to use the Reentry guide. It's fairly straightforward.

rentry.org/EmuNANDNewSDcard

 

[GravityLoL]

I'm not sure what you mean about "break up" but this is standard stuff. You're copying to a new SD card, right? It would be a lot easier if you used file-based emuNAND. You should be able to copy the partition and I think the system would still find it but I haven't tested it. You may want to use the Reentry guide. It's fairly straightforward.

rentry.org/EmuNANDNewSDcard

i found people saying HDD Raw copy tool can be used to backup emunand . gonna try it that way

 

[grooster]

i found people saying HDD Raw copy tool can be used to backup emunand . gonna try it that way

Okay. Good luck!

 

[pupuz]

Hello, third week messing up with my failed Switch, trying to simplify my question - I've been told to make emuNAND backup with NXNandManager with the goal to import my saves later. How does the import work? I don't see any import option in JKSV, and my saves are just emuNAND USER/SAVE files named 0000000000a, 00000000000b etc, not JKSV backups.

 

[Draxzelex]

In the past, I could press "B" to exit hbmenu. That isn't working now. Is there a setting to make it exit that way?

I don't ever remember the "B" button being able to exit the homebrew menu. The only way you can exit is by pressing the Home button.

When I open hekate on my Switch, it keeps saying it's in 1bit mode. Which is funny because it reads the card no problem at least NOW it does and I haven't had this issue until just recently nor have I done anything to the pins. I'd open it up if to check if I could but I don't even know what screwdriver the Switch uses and I'm afraid of damaging my Switch.
This has happened ever since i upgraded to 14.1.2 and then 15.0.0 and while my Switch works normally otherwise, I'm getting more worried by the minute. It happened with my 1TB SD Card all of a sudden and before that It never happened with any prior cards. The card is Sandisk too. I think it's an issue with the sigpatches as I just installed them.
Update: I tried a rather unorthodox solution by searching the forum and found that if I apply pressure to the sd card reader it will sometimes go past the original check. Unfortunately this leads to other problems, like my Switch not wanting to accept hekate, and I feel like I've exhausted every possibility besides taking it apart, and I really don't want to do that. I just know some people said on this forum that if the pins are even slightly loose it can mess things up big time. As I said this is ONLY when trying to use CFW, everything else works perfectly.

Its absolutely impossible that your issue is related to patches, They aren't even applied when you initially open Hekate. The problem is what you fear the worst which is a damaged SD card reader. The reader is very fragile and can break without you touching the pins; it can break from the normal usage of ejecting and injecting the SD card. Anyways, If you don't want to open it up, then you can try taking it to a repair shop for them to take a look at instead.

Hello everyone,
I downgrade my switch from 14.1.2 to 4.1.0 using daybreak on my sysnand to unlock the possibility of use pegascape.
Now my switch don't boot up anymore, I can only launch hakate from RCM.
I have no backup...
Anyone can help me?

First of all, why on earth would you downgrade? The RCM exploit is better than the pegascape exploit. Secondly, the reason you can only launch Hekate from RCM is because you downgraded to a firmware lower than your current fuse count. You see, the Switch has anti-downgrade fuses that are burnt every time you update to a major firmware. When there are burnt, you cannot boot the console to a firmware lower than the number of fuses burnt. Luckily, the RCM exploit is triggered before the fuse count so it can allow us to bypass the fuse check. But that's where the utility ends. In order for you to use Pegascape in your console's current condition, you have to use the RCM exploit first to bypass the fuse check. At that point, you might as well just use the RCM exploit. Downgrading to a firmware higher than your fuse count just to use an inferior exploit like Pegascape is a very stupid and dangerous thing. You should be thankful you can still use Hekate. Update your firmware back to 14.1.2 by using the homebrew app Daybreak and never ever do something this idiotic again.

Hello, third week messing up with my failed Switch, trying to simplify my question - I've been told to make emuNAND backup with NXNandManager with the goal to import my saves later. How does the import work? I don't see any import option in JKSV, and my saves are just emuNAND USER/SAVE files named 0000000000a, 00000000000b etc, not JKSV backups.

I'll admit that I haven't been following your dilemma for the past 3 weeks but if your goal is ultimately to recover save data from emuMMC, you can try following this tutorial.

 

[pupuz]

I'll admit that I haven't been following your dilemma for the past 3 weeks but if your goal is ultimately to recover save data from emuMMC, you can try following this tutorial.

Thanks! but this one says they had the previous Checkpoint backup to make it work and I don't have one.

 

[Draxzelex]

Thanks! but this one says they had the previous Checkpoint backup to make it work and I don't have one.

I don't think you need a previous backup to make it work. I believe the previous backups are just to help identify which save is which.

 

[GravityLoL]

okay, so my SD card migration has gone wrong, i guess.
I did emunand dump, both boot0 and boot1 dump, restored the dump using NxNadManager and...atmosphere doesnt load
" can't load sdmc/atmosphere/package3!"
looking at things through hekate, i noticed whole space of SD card is unocupied, which means something bucked up at Emunand. so there goes me asking:
should i place emunand dump on SD card and restore it using hekate or should i do something else?
What are you guys saying?

 

[pupuz]

It worked, thanks

 

[Draxzelex]

okay, so my SD card migration has gone wrong, i guess.
I did emunand dump, both boot0 and boot1 dump, restored the dump using NxNadManager and...atmosphere doesnt load
" can't load sdmc/atmosphere/package3!"
looking at things through hekate, i noticed whole space of SD card is unocupied, which means something bucked up at Emunand. so there goes me asking:
should i place emunand dump on SD card and restore it using hekate or should i do something else?
What are you guys saying?

According to SciresM, you either didn't extract all of the Atmosphere files to your SD card or have the archive bit set on your /atmosphere folder.

My journey through hacking my NSW using RCMLoader. Context:

• I'm using the great guide https://switch.homebrew.guide/gettingstarted/beforestarting.html
• I'm also relying on the RCMLoader (old version) to send the payload

Issues I found, and how I overcome them:

• The RMCLoader seemed to work but the NSW never left the black screen
  • Solution: 1) stick to the old payload.bin or 2) update the firmware (requires Windows) https://www.xkit.xyz/support/
• It booted but then "A fatal error occurred when running Atmosphere. Title ID: 010041544d53000"
  • Solution: I was "forced" to stick to the #2 prev solution (aka update the firmware)
• NSW went further but then it stopped by the "error code 2168-0001 & 2168-0002"
  • Solution: it turns out my sd setup was telling me that I was using FAT32 and exFAT https://github.com/Atmosphere-NX/Atmosphere/issues/1881#issuecomment-1132230518 I just formatted my sd card into FAT32
• It seems to be working fine

Questions:

• What's the tradeoff between FAT32 and exFAT on CFW NSW?
• Does anyone know how to update the RMCLoader firmware using Linux/Mac? (actually what's is the firmware on this dongle )
• How can I update the toolchain? (cfw, bootloader, ....)
• Any advice?

• There is no tradeoff. FAT32 is superior to exFAT. exFAT can corrupt your SD card unlike FAT32 and there are numerous ways to bypass the 4 GB limit on FAT32 such as USB or wireless installations
• The site maybe hasn't been fully updated. On this page, it indicates that there is support even on Linux and MacOS
• That'll depend on what exactly you need updating since each part is utilized differently. CFW are just files on the SD card so you can just download the latest CFW and put them on the SD card. The bootloader in your case is the bootloader files on your RCM Loader which you update according to the site

 

[prof72]

Tinfoil stops working 3 months already

my nswitch system

Current Version 14.1.2 | AMS 1.3.2|S

can i fix it? or tinfoild is dead?
i can see the website link address but its not highlighted

save share and some are working but not game download and dlc and update