Hacking sx pro boot cfw without jim by accident will burn fuse also i dont use autorcm

[sh2dc]

hi my question is:
sx pro boot cfw without jim by accident will burn fuse?
also i dont use autorcm

i just complete shut down everything never use sleep mode

boot cfw use tx pro everytime with loader + jim

will fuse burn over????


what if i boot ofw with jim ??

is it safe?

 

[sh2dc]

yesterday night i boot cfw seems i accident move jim "a bit" by use a 3rd ipega 9083 gamepad when fit into switch


it boot into cfw fine

but i heard something happen in console pcb board when boot

am i screwed?!

 

[LyuboA]

burned fuses are no longer an issue you can use any firmware you want dosnt matter the fuses
and better enable autorcm its very convenient dont have to use jig everytime and no theres no battery
issue unless you left your Switch into RCM mode but since all CFWs can now completely shutdown
the console normally "power button - turn off" its all fine
i use AutoRCM for over very long time never had an issue and no the battery dosnt drain faster with AutoRCM

 

[M7L7NK7]

Jim lmao

 

[Dust2dust]

Jim lmao

Jim is his buddy, from what I understand. He's not confident enough to start his Switch in CFW without Jim being present to help him. Once OP gets used to doing it by himself, Jim will not have to be in the same room anymore, and can be somewhere else doing his own business.

 

[sh2dc]

burned fuses are no longer an issue you can use any firmware you want dosnt matter the fuses
and better enable autorcm its very convenient dont have to use jig everytime and no theres no battery
issue unless you left your Switch into RCM mode but since all CFWs can now completely shutdown
the console normally "power button - turn off" its all fine
i use AutoRCM for over very long time never had an issue and no the battery dosnt drain faster with AutoRCM

but i heard something happen in console pcb board when boot

so im in mistake ?

theres nothing wrong?!

 

[LyuboA]

but i heard something happen in console pcb board when boot

so im in mistake ?

theres nothing wrong?!

you are ok dosnt matter that you burned the fuses like i said all CFWs can bypass them now
and you can boot into OFW from SXOS boot menu

 

[Hayato213]

hi my question is:
sx pro boot cfw without jim by accident will burn fuse?
also i dont use autorcm

i just complete shut down everything never use sleep mode

boot cfw use tx pro everytime with loader + jim

will fuse burn over????


what if i boot ofw with jim ??

is it safe?

If you boot without custom bootloader then your fuse would be burnt. If you don't care about going back to lower firmware no need of AutoRCM.

 

[LyuboA]

If you boot without custom bootloader then your fuse would be burnt. If you don't care about going back to lower firmware no need of AutoRCM.

you can go back to lower firmware with burned fuses for a very long time now since like i said twice already
ALL CFWs can bypass fuses and AutoRCM is a Big convenience ppl use it primary for not having to use a jig
every time not for saving fuses that no longer matter in any way

 

[Hayato213]

you can go back to lower firmware with burned fuses for a very long time now since like i said twice already
ALL CFWs can bypass fuses and AutoRCM is a Big convenience ppl use it primary for not having to use a jig
every time not for saving fuses that no longer matter in any way

Sure if that was only applying to 1-2 burnt fuse different, if you downgrade to something with much higher fuse count different the system start to panic and refuse to boot even with a custom bootloader. Technically OP can solder the SX Pro on to his motherboard and use AutoRCM that would be a lot easier that using the jig and the dongle everytime.

 

[LyuboA]

Sure if that was only applying to 1-2 burnt fuse different, if you downgrade to something with much higher fuse count different the system start to panic and refuse to boot even with a custom bootloader. Technically OP can solder the SX Pro on to his motherboard and use AutoRCM that would be a lot easier that using the jig and the dongle everytime.

ya but show me 1 normal user that wants to go back 5 OFW versions hell they update the moment new update is out
so most ppl dont care you will mostly need to go back 1 or 2 version no more and for the autorcm its easy to enable
not so easy to solder a board to your Switch that you may want to sell some day

 

[Hayato213]

ya but show me 1 normal user that wants to go back 5 OFW versions hell they update the moment new update is out
so most ppl dont care you will mostly need to go back 1 or 2 version no more and for the autorcm its easy to enable
not so easy to solder a board to your Switch that you may want to sell some day

https://gbatemp.net/threads/downgraded-from-10-1-to-6-1-and-now-sx-os-black-screen.579034/

This is a good example the guy went from 10.1.0 to 6.1 now his unit refuse to boot.

 

[LyuboA]

https://gbatemp.net/threads/downgraded-from-10-1-to-6-1-and-now-sx-os-black-screen.579034/

This is a good example the guy went from 10.1.0 to 6.1 now his unit refuse to boot.

well what can you do Stupidity is NOT an excuse he dosnt need supid DevMenu that works on 9.2.0
he could just have used DBI works much better then this very outdated devmenu but hey they never read