Hacking NTR 3.4 Screen Recorder Test Thread

[smileyhead]

i was able to connect now but after i tried remote play i got this
> remoteplay()
null
Will be disconnected in 10 seconds to enhance performance.
cpu was locked on 804MHz, L2 Enabled
starting remoteplay...
buf: 07001000, size: 00022000
remotePC: 001231d0
> disconnect()
null
Unable to read data from the transport connection: A blocking operation was interrupted by a call to WSACancelBlockingCall.
Server disconnected.

That's normal. Just open NRTViewer.

 

[mariobear]

That's normal. Just open NRTViewer.

are you sure i just did that and now its a white screen. i enabled the debugger on 3ds then open up debugger on pc then the view

 

[Selim873]

Took me a while to finally find the settings that worked for me. Here you go!!



NTR CFW 3.4 Preview 2
OS: Windows 10 x64
Recording program: OBS Multi-Platform (Latest)
NTRViewer Settings: Top, 1.0. Bottom, 0.0 (Off)
Remote Play command:

remoteplay(priorityMode = 0, priorityFactor = 5, quality = 70, qosValue = 100)

PC is hardwired, and I'm literally sitting right next to my router with my N3DS. This is the absolute best I could do without getting most frames dropped.

 

[NekoMichi]

Remote Play command:

remoteplay(priorityMode = 0, priorityFactor = 5, quality = 70, qosValue = 100)

PC is hardwired, and I'm literally sitting right next to my router with my N3DS. This is the absolute best I could do without getting most frames dropped.

If you're only streaming one screen, use a proprityFactor of 0 because this will disable the non-streaming screen entirely and free up more bandwidth to allow better quality streaming.

 

[mariobear]

yes i got it to work

 

[mariobear]

any suggestions on making it abit un pixelated?

 

[shadowofdarkness]

It only took 6 hours of this but I got a video worth putting up. It gets interesting around the minute mark.

Streamed to and recorded on a Linux laptop. NTR reported a usual frame rate of 32-41 fps My laptop is over six years old so the recording was not a smooth as the ntrviewer window.

 

[NekoMichi]

any suggestions on making it abit un pixelated?

Use a quality number around 90-100 to reduce the pixel blocking effect.

 

[Phil5004]

Okay, I still cant connect it..

 

[NekoMichi]

Okay, I still cant connect it..

Does your router have a guest mode? Some routers do not allow device-to-device communications under guest mode.

 

[cavolo]

It only took 6 hours of this but I got a video worth putting up. It gets interesting around the minute mark.

Streamed to and recorded on a Linux laptop. NTR reported a usual frame rate of 32-41 fps My laptop is over six years old so the recording was not a smooth as the ntrviewer window.

Hey, how do you get it work on linux ? I'm stuck because of .NET... If I install the .NET4, the debugger ask me to install 4.5, and if I try to install 4.5, it fail

 

[Phil5004]

Does your router have a guest mode? Some routers do not allow device-to-device communications under guest mode.

I dont think so... If it helps:
My Wifi Router is a "Speedport W 503" with a "Fritzbox" Firmware...
BTW. Can I use my HTC one M7 for my N3DS to connect it on my PC?

 

[NekoMichi]

I dont think so... If it helps:
My Wifi Router is a "Speedport W 503" with a "Fritzbox" Firmware...
BTW. Can I use my HTC one M7 for my N3DS to connect it on my PC?

Good idea, try using your HTC as an alternative router. If you can connect your debugger through your phone, then we can isolate the Speedport as the source of the problem.

Remember to re-check your 3DS' IP address after switching from your router to your HTC as the IP address will change.

 

[Phil5004]

Okay, Finally it worked on my HTC
But I cant Stream on Twitch with my Mobile Wifi.
Can I create a host on my PC (Virtual Router) And can use my usual Router ?

 

[NekoMichi]

Okay, Finally it worked on my HTC
But I cant Stream on Twitch with my Mobile Wifi.
Can I create a host on my PC (Virtual Router) And can use my usual Router ?

That might be possible.
It looks like something's wrong with the Speedport, which is preventing device communications. Your PC should work as a suitable host.

 

[Xenon Hacks]

Took me a while to finally find the settings that worked for me. Here you go!!



NTR CFW 3.4 Preview 2
OS: Windows 10 x64
Recording program: OBS Multi-Platform (Latest)
NTRViewer Settings: Top, 1.0. Bottom, 0.0 (Off)
Remote Play command:

remoteplay(priorityMode = 0, priorityFactor = 5, quality = 70, qosValue = 100)

PC is hardwired, and I'm literally sitting right next to my router with my N3DS. This is the absolute best I could do without getting most frames dropped.

Says I cant watch your video because you disabled playback on other sites

 

[Phil5004]

What was the Command to use NTR Viewer in Fullscreen? Or larger than the real one?

--------------------- MERGED ---------------------------

That might be possible.
It looks like something's wrong with the Speedport, which is preventing device communications. Your PC should work as a suitable host.

Which Program should I use? I've tested VIrtual Router and Connectify and no one worked

 

[NekoMichi]

What was the Command to use NTR Viewer in Fullscreen? Or larger than the real one?

--------------------- MERGED ---------------------------


Which Program should I use? I've tested VIrtual Router and Connectify and no one worked

To enlarge NTRViewer, you'll have to open it through the command prompt and add -t 3.0 -b 3.0 at the end of the command.

I think Windows has a native Internet sharing feature, but it requires the PC to be connected via Ethernet. (Unfortunately I don't know how to set up the feature because I'm not using Windows as the base OS on my machine)

 

[Selim873]

Says I cant watch your video because you disabled playback on other sites

Fixed

 

[Giodude]

I just upgraded all the way from the initial release of aureinand to Luma3ds 5.2. Now ntr cfw says unknown firm wand then crashes. What do i do?

EDIT: it stores the firm in LUMA instead of AUREI im an idiot nvm