It seems the way they have everything written this is making you update the emunand and not the sysnand. At least following the directions that is what I did since my nands are unlinked, yet my emunand was modified instead of the sysnand
BigBlueMenu doesn't seem to install it, however DevMenu.3ds worked for me, although i still can't get the exploit to boot the Gateway Menu
Here's what i've attempted:
1. Booted Gateway Menu 3.2 using OoT Exploit on n3DS XL 9.0
2. Installed NVRAM
3. Hex Edited the Physical Drive of my SD Card using Hex Workshop (Changed the first line GATEWAYNAND to FATEWAYNAND) to block emunand from opening (Worked fine, could tell by my cia's being missing and my theme was the same as my sysnand)
4. Ran DevMenu.3ds and installed the mset_eur.cia, Installed Successfully
5. Rebooted my n3DS and went into Nintendo DS Profile
6. Nothing proceeded to happen, opened as it would normally
this is a AUS N3DS XL, not sure if it makes any difference as the firmware is still 9.0.0-20E
seems like its "unfinished"
works fine for me on my AUS n3DS XL on 9.0.0-20EBigBlueMenu doesn't seem to install it, however DevMenu.3ds worked for me, although i still can't get the exploit to boot the Gateway Menu
Here's what i've attempted:
1. Booted Gateway Menu 3.2 using OoT Exploit on n3DS XL 9.0
2. Installed NVRAM
3. Hex Edited the Physical Drive of my SD Card using Hex Workshop (Changed the first line GATEWAYNAND to FATEWAYNAND) to block emunand from opening (Worked fine, could tell by my cia's being missing and my theme was the same as my sysnand)
4. Ran DevMenu.3ds and installed the mset_eur.cia, Installed Successfully
5. Rebooted my n3DS and went into Nintendo DS Profile
6. Nothing proceeded to happen, opened as it would normally
this is a AUS N3DS XL, not sure if it makes any difference as the firmware is still 9.0.0-20E
seems like its "unfinished"
Make sure you to go to settings and check if it doesn't say GW infront of the version number, because it could just create another emuNAND partition for you
There's maintenance today up to midnight (by the way guys anyone knows if the nintendo update servers is down or not ? i'm trying to update an old 3ds from 9.5 to 9.7 but the update process will not start !
it will always boot to emunand if you leave emunand set up regardless of if its linked or not, just use a different SD cardIt seems the way they have everything written this is making you update the emunand and not the sysnand. At least following the directions that is what I did since my nands are unlinked, yet my emunand was modified instead of the sysnand
DarkKaine read earlier posts, the newer DevMenu (BigBlueMenu) doesn't like to import it, but an older one will happily import.
There's maintenance today up to midnight (France time).
http://www.nintendo.com/consumer/network/fr_na/network_status.jsp
it will always boot to emunand if you leave emunand set up regardless of if its linked or not, just use a different SD card
I want to update my games i couldnt so far. But Estore down?
People stop worrying about losing the ability to calibrate 3D. You can just calibrate it while in emunand since emunand won't have the downgraded System Settings (assuming you downgrade it properly). Calibration settings can be independent on emunand. You only lose the ability to calibrate it while on sysnand.
dang, is this confirmed?, anyone else still got Super Stable 3D calibration in emunand?, seems like NVRAM installed onto my emunand due to the fact my SD card had emunand on it at the time, if this is the case, i could potentially download and install a n3DS System Settings cia for 9.5.0(for my emunand) correct?