Homebrew snes emulator released

[yardie]

got it to work
some steps are missing in the tuts

when you connect your switch to pegaswitch you have to run:

evalfile usefulscripts/SetupNew.js

inside of pegaswitch terminal not regular terminal

 

[EvilG31]

got it to work
some steps are missing in the tuts

when you connect your switch to pegaswitch you have to run:

evalfile usefulscripts/SetupNew.js

inside of pegaswitch terminal not regular terminal

Yeah - It's mentioned briefly on github. I didn't realize it was a mandatory step either. Did you have any issues with ncat providing the switch's IP address?

 

[yardie]

Yeah - It's mentioned briefly on github. I didn't realize it was a mandatory step either. Did you have any issues with ncat providing the switch's IP address?

heres what i did after doing the eval file bit

ncat -l -p 2991
runnro ./nros/ace.nro

then i see the ip

 

[Deleted User]

THANKS SO MUCH FOR EVERYONE HELP HERE let us not fight amongst ourselves! Thanks to all the comments I will reattempt as I had issues before.

 

[Greg956]

After I write runnro ./nros/ace.nro Pegaswitch terminal write unknown cmd

 

[Deleted User]

well some things I have learned in Windows 10 with linux subsystem attempting requires admin rights for all the terminals and the pathing is case sensitive so far I have only gotten to run the ace.nro successfully once but then it spat back an issue with admin rights when i tried to load retroarch. I have tried several times since with no luck to get ace to reload again. Must I issue the enable sdbcore command prior to connecting the switch each time (even if I don't close my pegaswitch session?) must I run the evalfile usefulscripts/SetupNew.js command each time I connect via pegaswitch?

Also I couldn't get this far till I updated pegaswitch so just a heads up and for some reason I could not install latest npm not sure why though I get prompted to update.

ok i got further I am actually like hanging at the screen to load the retroarch nro but connection keep timing out I imagine both those commands must be inputed each attempt any ideas if connection time out just keep trying or start over?

Ok I can get my switch ip to pretty much show reliably in ncat now but still no joy any idea if this is just not compatible with dock mode?

 

[TheGreek Boy]

when i'm running "runnro ./nros/ace.nro" my switch gets back at switch system settings and then i run the command "ncat --send-only 192.168.1.6 2991 home/pegaswitch/pegaswitch/nros/retroarch_switch.nro" and terminal says "more than 1 port QUITTING" or something like that

 

[Deleted User]

Yeah I was just about to say I think this is a port issue I have double checked everything and once I see my switch ip I can't seem to send retroarch. So that number in the command "SWITCHIP 2991" I am assuming this is a port I need to open no?

 

[x0x0]

when i'm running "runnro ./nros/ace.nro" my switch gets back at switch system settings and then i run the command "ncat --send-only 192.168.1.6 2991 home/pegaswitch/pegaswitch/nros/retroarch_switch.nro" and terminal says "more than 1 port QUITTING" or something like that

Before running ace.nro open terminal and type - dont close this.
nc -v -l -p 2991

connect to pegaswitch by check update in any game
runnro /nros/ace.nro
(if it hung system, without error code u fine)

open next terminal then
ncat --send-only 192.168.1.6 2991 < location to your nro

symbol < is important.

 

[TheGreek Boy]

Before running ace.nro open terminal and type - dont close this.
nc -v -l -p 2991

connect to pegaswitch by check update in any game
runnro /nros/ace.nro
(if it hung system, without error code u fine)

open next terminal then
ncat --send-only 192.168.1.6 2991 < location to your nro

symbol < is important.

i will try that now

--------------------- MERGED ---------------------------

YESSSSSS WORKED I'M PLAYING SECRET OF MANA THANKS

 

[urherenow]

wait... why are people sharing it here, and why are mods not deleting it? It has a freaking ROM built-in! You can't distribute or even link to a ROM from this site!

 

[Somario]

Finally got it to work after about 2 hours of resetting switch. Thanks for the instructions @ehnoah !

The music is too fast compared to the original for snes, I presume the game will be too fast too, I think the emulator has to be perfected but very good work!

 

[Deleted User]

success video coming with tut

 

[ehnoah]

see, isn't that hard New RetroArch support MutliRom etc.

 

[Deleted User]

im tired and it's hard to explain but I got alot going on i made really dumb mistake and wrote switch ip in my command



Instructions
Load Pegaswitch
Run following in Pegaswitch:
enable sdbcore
evalfile usefulscripts/SetupNew.js
Open 2 cmd promps with Admin rights and enter Bash enter following cmd in one window:
nc -v -l -p 2991
Back to pegaswitch enter:
runnro ./nros/ace.nro
Now use the other terminal window. As in video I recommend cd till you are in your nro folder from here enter:

ncat --send-only 192.168.0.2 2991 < retroarch_switch.nro

Replace my ip with yours.

 

[Greg956]

After I write runnro ./nros/ace.nro Pegaswitch terminal write unknown cmd

Again and again, Pegaswitch terminal writes unknown cmd.

 

[x0x0]

Again and again, Pegaswitch terminal writes unknown cmd.

you probably have old pegaswitch, without runnro command.

 

[Greg956]

you probably have old pegaswitch, without runnro command.

So, how to delete it and copy new one?

 

[Nezztor]

im tired and it's hard to explain but I got alot going on i made really dumb mistake and wrote switch ip in my command



Instructions
Load Pegaswitch
Run following in Pegaswitch:
enable sdbcore
evalfile usefulscripts/SetupNew.js
Open 2 cmd promps with Admin rights and enter Bash enter following cmd in one window:
nc -v -l -p 2991
Back to pegaswitch enter:
runnro /nros/ace.nro
Now use the other terminal window. As in video I recommend cd till you are in your nro folder from here enter:

ncat --send-only 192.168.0.2 2991 < retroarch_switch.nro

Replace my ip with yours.

Congrats ! I will add your video to the post

 

[x0x0]

So, how to delete it and copy new one?

in terminal
git clone https://github.com/reswitched/pegaswitch
cd ~/pegaswitch
npm install
sudo node start.js