Hardware Sd card write protected

  • Thread starter Thread starter Jdr967
  • Start date Start date
  • Views Views 12,170
  • Replies Replies 15

Jdr967

New Member
Newbie
Joined
Apr 30, 2017
Messages
2
Reaction score
0
Trophies
0
Age
29
XP
81
Country
United States
Hi everyone! I started using a 32gb micro sd card for the wii u, and all of a sudden, it became write protected.
The thing is it still works on the wii u, but i can't use it on a pc. Any help please?
 
Before i jump to conclusion: Check if your SDCard "mother" card isn't set to "read only" [White block switch]. If it's set as r/w and still reports as read only, It got corrupted. Most SDCards [Overally flash memory] make themselves as read to prevent further corruption.
 
Before i jump to conclusion: Check if your SDCard "mother" card isn't set to "read only" [White block switch]. If it's set as r/w and still reports as read only, It got corrupted. Most SDCards [Overally flash memory] make themselves as read to prevent further corruption.
Exactly

Make sure the little yellow/white/whatever switch is pushed upward, not downward

If that doesn't work I will gladly copy and paste you a guide, because your laptop might be stupido
 
Format it in PC with guiformat see if it's able to format.
Sometimes forcefully formating SDCards fixes it. Atleast in my case.
If it gives errors then you should probably get a new one and trash your old one. [Be sure to break it or those collecting trash will dump data from it ;) [Probably]
 
Format it in PC with guiformat see if it's able to format.
Sometimes forcefully formating SDCards fixes it. Atleast in my case.
If it gives errors then you should probably get a new one and trash your old one. [Be sure to break it or those collecting trash will dump data from it ;) [Probably]
i tried that but it failed
 
Format it in PC with guiformat see if it's able to format.
Sometimes forcefully formating SDCards fixes it. Atleast in my case.
If it gives errors then you should probably get a new one and trash your old one. [Be sure to break it or those collecting trash will dump data from it ;) [Probably]
i tried that but it failed
 
i tried that but it failed
If it doesn't format under any circumstances, it's dead. The Wii U operating system constantly writes to Wii U formatted storage, which is why it's recommended to use a USB hard drive instead of SD cards or flash drives. Most likely it reached its write limit because of that.

It's a little deceptive because although it's "dead" you can usually still access the files that were already on there. You just can't write anything more to it or even delete anything. Same things happen sometimes with SD cards in phones.
 
The "little switch" you are referring to is a tab that pushes a little button inside the slot that tells the computer it is in write mode. It does not connect electrically to any part of the SD card; it is part of the case like a record tab on a cassette tape. If the card is in read only mode in both tab states and across computers, then the card has a faulty curcuit. If the slot does this to any SD card, then the button in the slot is likely damaged and the slot will need to be replaced. If the tab falls off and you lose it, you will have to put tape over the tab track to write to the SD card again.
 
Last edited by kehkou,
I'm having a problem where my Wii U keeps saying I have write protection but It's fine on my PC. Any help?
Delete and cut work on the sd while in the pc? The locking mechanism may be at fault. I have an SD card that has a very loose tab, so it gets flipped to lock while inserting the card.
 
fixed It by putting tape around the SD Card
Man... you saved my life with that !!!
Thank you.

I can't understand what happened, i tried 2 others SDcard, same result = readonly
(the lock is not moving when inserting)

This must have something to do with the wii-U SDCard plug...
 
Last edited by Laf111,
@Laf111 The Wii U uses a laser to read out the switch. Laser blocked = read/write, laser passing = read only.
Now this laser is positioned so badly that a real small split between the casing of the adapter and the switch is enough for the laser to pass through... This split might be so small, you can't even see it... And that's where the tape comes in: It will block the laser no matter what. ;)
 

Site & Scene News

Popular threads in this forum