Homebrew Help 10.3 update ironhax problem

[Juan2416]

So I just update the payload then update the system so when I start ironhax and it just show the load then back to home menu

 

[gallymimu]

can you restate your question... assuming you have one. Your post doesn't make a lot of sense to me.

I am assuming you updated the payload, then updated the system(not sure what that means the 3ds firmware to 10.3?)

 

[sauroa]

i have the same problem, i was using 10.1, updated the payload compatible with 10.3, updated to 10.3 and now ironhax crash after "the homemenu ropbin is ready" =/

 

[anonynom]

After you updated the payload, you did reinstall ironhax to OLD / NEW 10.3 correct?

 

[Juan2416]

After you updated the payload, you did reinstall ironhax to OLD / NEW 10.3 correct?

What you mean reinstall

 

[YukiHomura]

you have to reinstall ironhax after payload update

 

[Juan2416]

you have to reinstall ironhax after payload update

Is it the same thing as update the payload

 

[Eskuero]

Are you sure you choose correctly your ironfall version as your 3ds 10.3 firmware?
I mean if you choose also the correct region and select correctly if you have O3DS or N3DS?

 

[animefreak55]

You were supposed to copy the new starter zip before you updated the firmware. Then after updating you have to run the ironhax installer again to get it to work on 10.3.

 

[Eskuero]

Wait wait wait wait

1. You grab the ironhax installer from latest starter kit.
2. You get to hbl and run it.
3. You choose your Ironfall version (either 1.0 or 1.1) and the slot you want to install to.
4. You choose if your 3DS is the OLD version or the NEW one.
5. You select 10.3 as the firmware version as is the one you're updating to.
6. You choose if your 3DS is EUR or USA region.
7. It should download the proper payload and install ironhax without asking anything else.
8. Now you update your 3DS firmware to 10.3
9. IronHax should be working again.

Isn't those the correct steps? What did you do?

 

[animefreak55]

Wait wait wait wait

1. You grab the ironhax installer from latest starter kit.
2. You get to hbl and run it.
3. You choose your Ironfall version (either 1.0 or 1.1) and the slot you want to install to.
4. You choose if your 3DS is the OLD version or the NEW one.
5. You select 10.3 as the firmware version as is the one you're updating to.
6. You choose if your 3DS is EUR or USA region.
7. It should download the proper payload and install ironhax without asking anything else.
8. Now you update your 3DS firmware to 10.3
9. IronHax should be working again.

Isn't those the correct steps? What did you do?

Maybe I did more than I had to? The more important question is what did OP do?

 

[sauroa]

Wait wait wait wait

1. You grab the ironhax installer from latest starter kit.
2. You get to hbl and run it.
3. You choose your Ironfall version (either 1.0 or 1.1) and the slot you want to install to.
4. You choose if your 3DS is the OLD version or the NEW one.
5. You select 10.3 as the firmware version as is the one you're updating to.
6. You choose if your 3DS is EUR or USA region.
7. It should download the proper payload and install ironhax without asking anything else.
8. Now you update your 3DS firmware to 10.3
9. IronHax should be working again.

Isn't those the correct steps? What did you do?

OHHHH, when i was updating ironhax, i was unable to change the firm ver, so i left 10.1.... now that was my problem!

well... Time to make my Ocarina of Time a Entrypoint =(

Thx for the info

 

[Eskuero]

OHHHH, when i was updating ironhax, i was unable to change the firm ver, so i left 10.1.... now that was my problem!

well... Time to make my Ocarina of Time a Entrypoint =(

Thx for the info

I think Ocarina of Tima it's not independent and you need another entrypoint already set-up to install it

 

[sauroa]

I think Ocarina of Tima it's not independent and you need another entrypoint already set-up to install it

yep, i know, i will try to borrow a 3DS =P, thx again!

 

[anonynom]

Wait wait wait wait

1. You grab the ironhax installer from latest starter kit.
2. You get to hbl and run it.
3. You choose your Ironfall version (either 1.0 or 1.1) and the slot you want to install to.
4. You choose if your 3DS is the OLD version or the NEW one.
5. You select 10.3 as the firmware version as is the one you're updating to.
6. You choose if your 3DS is EUR or USA region.
7. It should download the proper payload and install ironhax without asking anything else.
8. Now you update your 3DS firmware to 10.3
9. IronHax should be working again.

Isn't those the correct steps? What did you do?

This is what I did ^

 

[Juan2416]

Wait wait wait wait

1. You grab the ironhax installer from latest starter kit.
2. You get to hbl and run it.
3. You choose your Ironfall version (either 1.0 or 1.1) and the slot you want to install to.
4. You choose if your 3DS is the OLD version or the NEW one.
5. You select 10.3 as the firmware version as is the one you're updating to.
6. You choose if your 3DS is EUR or USA region.
7. It should download the proper payload and install ironhax without asking anything else.
8. Now you update your 3DS firmware to 10.3
9. IronHax should be working again.

Isn't those the correct steps? What did you do?

Oh ok I mess up I forgot to put it to 10.3